Majestic fireplaces DVB4136 Скачать руководство пользователя

Страница: 43 / 52

DVB4136 Direct Vent Gas Fireplace

20012322

CO105

Gas Conversion

Pilot

2/15/99 djt

Index

Marks

Pilot

Bracket

Pilot Hood

CO105

Fig. 74

Remove pilot hood.

CO106

Gas Conversion

Pilot2

2/15/99 djt

Pilot

Oriﬁce

CO106

Fig. 75

Remove pilot oriﬁce.

2.  Remove pilot oriﬁce with needlenose pliers. (Fig. 75)
3.  Install conversion pilot oriﬁce.
4.  Reinstall pilot hood. Be sure to align pilot hood with

index marks.

Pilot Oriﬁce Conversion

NOTE:

It is not necessary to remove the pilot tube for

conversion.

1. Loosen pilot hood turning counterclockwise using a

7/16” wrench. (Fig. 74)

5. Turn the gas supply valve and gas valve on and test

for leaks. Use a 50/50 solution of liquid soap and
water to test for leaks at gas ﬁttings and joints. Apply
water/soap solution with brush only -

do not over ap-

ply.

NEVER test with an open ﬂame.

6. Follow procedure on rating plate to light the pilot.

Check for leaks.

7. Turn main burner on and check for leaks.
8. Install logs. Refer to Page 25 for proper log place-

ment.

Installation complete.

Conversion to Natural Gas

Minimum

Burner Oriﬁce

Input (BTU/hr)

Kit #

Model

Rate Scew

Front

Part #

Rear

Part #

Minimum Maximum

DVB4136RP

n/a

#57

20002409

#41

20004801

18,500 30,000

20013165

(.043”)

(.096”)

DVB4136RFP/IP No ﬂow restr.

#57

20002409

#39

20013150

18,500 30,000

20012264

(.043”)

(.0995”)

Conversion to LP

Minimum

Burner Oriﬁce

Input (BTU/hr)

Kit #

Model

Rate Screw

Front

Part #

Rear

Part #

Minimum Maximum

DVB4136RN/RFN

n/a

#66

55143

#54

20002150

17,000 30,000

20013166

(.033”)

(.055”)

DVB4136IN

#54

#66

55143

#53

54833

17,000 30,000

20013177

(.033”)

(.0595”)

Table 1 Injector Oriﬁce Size Matrix

Table 2 Air Shutter Setting

Model

Fuel Type

Front

Rear

DVB4136RP/RFP/IP

1/4” Open

Round Hole 1/2 Open

DVB4135RN/RFN/IN

Natural

1/2” Open

Fully Open

Содержание DVB4136





















































Результаты поиска

Содержание DVB4136

Отзывы:

Похожие инструкции для DVB4136

Бренды по названию

Популярные бренды

Majestic fireplaces DVB4136, Руководство по установке и эксплуатации для владельцев жилья

Результаты поиска

Содержание DVB4136

Отзывы:

Похожие инструкции для DVB4136

Бренды по названию

Популярные бренды