Majestic fireplaces DVB4136 Скачать руководство пользователя

Страница: 26 / 52

DVB4136 Direct Vent Gas Fireplace

20012322

��
��
��

Replacement of

Ceramic Hearth Panels (if provided)

1. Remove glass.
2. Set left and right panels on hearth and bring towards

front of unit.

H100a

hearth Panels

1/27/00 djt

Screw

Burner

Hearth Panels

Grate

Front of Unit

H100a

Screw

Fig. 47

Hearth panel location (if provided).

Remove front glass. (Refer to “Window Frame As-
sembly Removal” Section, Fig. 46) Remove logs from
packaging.

As with all plastics — these are not toys
and should be kept away from children and
infants.

Installation of Logs

Log Identiﬁcation Chart

Logs

Part #

ID #

Top Right Log

20012595

B162

Left Log

20012596

B163

Rear Log

20012597

B164

Top Center Log

20012598

B165

Top Front Log

20012599

B166

Front Log

20012600

B167

NOTE:

Refer to Figure 48 for bracket locations.

1. Place the front log on the pins located on the front

brackets. (Fig. 48) Log should look like Figure 49.

��
��
��

Front Log

LG477

Figure 49

Front Brackets

Rear Log

Bracket

Front Brackets & Pins

FP1812

Figure 48

Rear Log

Stop Bracket

Содержание DVB4136





















































Результаты поиска

Содержание DVB4136

Отзывы:

Похожие инструкции для DVB4136

Бренды по названию

Популярные бренды

Majestic fireplaces DVB4136, Руководство по установке и эксплуатации для владельцев жилья

Результаты поиска

Содержание DVB4136

Отзывы:

Похожие инструкции для DVB4136

Бренды по названию

Популярные бренды