background image

- 18 -

10  YOUR GUARANTEE

Congratulations on purchasing a Stuart Turner Mainsboost Charger Pump. 

We are confident this product will give you many years of trouble free service as all 
our products are manufactured to the very highest standard. 

The Mainsboost Charger pump is covered by the 

three year

 guarantee.  

Within the guarantee period we will repair, free of charge, any defects in the  
Mainsboost Charger resulting from faults in material or workmanship, repairing or 
exchanging the part affected or whole unit as we may reasonably decide. 

Not covered by this guarantee: Damage arising from incorrect installation, improper 
use, unauthorised repair, normal wear and tear and defects which have a negligible 
effect on the value or operation of the unit. 

Reasonable evidence must be supplied that the product has been purchased within 
the guarantee term prior to the date of claim (such as proof of purchase or the 
product serial number). 

This guarantee is in addition to your statutory rights as a consumer.  If you are in any 
doubt as to these rights, please contact your local Trading Standards Department. 

In the event of a claim please telephone 

‘PumpAssist’

 customer support.

+44 (0) 800 31 969 80

You should obtain appropriate insurance cover for any loss or damage which is not 
covered by Stuart Turner Ltd in this provision.

Please record here for your records.

TYPE NO.

SERIAL NO.

DATE PURCHASED

Содержание Charger MBC 100SV





















Отзывы: