Main System 24 Eco Скачать руководство пользователя страница 18

Страница: 18 / 56

8.0 Flue Options

8.1

Horizontal Flue Systems

1. The standard flue is suitable only for horizontal termination
applications.

2. Maximum permissible equivalent flue lengths are:-

(60/100)

(80/125)

Horizontal Concentric

10 metres

20 metres

3. Any additional “in line” bends in the flue system must be
taken into consideration.
Their equivalent lengths are:-
Concentric Pipes:

135° bend

0.5 metres

93° bend

1.0 metres

Twin Flue Pipe

135° bend

0.25 metres

91.5° bend

0.50 metres

The elbow supplied with the standard horizontal telescopic
flue kit is not included in any equivalent length calculations

NOTE:

Flue length is measured from point (i) to (ii) as

shown.

IMPORTANT:

All flue systems must be securely supported

at least once every metre. Suitable pipe supports are
available as accessories.

Horizontal
Flues

(ii)

(i)

Plume Displacement Kit 60 /100 Ø

1M Extensions, 45° & 93° elbows

are also available - see Section 9.0

NOTE:

Horizontal flue pipes should always be installed with at least a 1.5° fall

from the terminal to allow condensate to run back to the boiler.

(ii)

(i)

This bend is equivalent to

1 metre

Total equivalent length =

A+B+C+2x90°Bends

This bend is equivalent to

1 metre

Supplied by HeatingSpares247.com

Содержание System 24 Eco

























































Результаты поиска

Содержание System 24 Eco

Отзывы:

Похожие инструкции для System 24 Eco

Бренды по названию

Популярные бренды

Main System 24 Eco, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System 24 Eco

Отзывы:

Похожие инструкции для System 24 Eco

Бренды по названию

Популярные бренды