Maico BSB FSD-TD Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

Maico BSB FSD-TD Series Скачать руководство пользователя страница 4

FSD-TD - Installation Operation and Maintenance Instructions

Page 4

6.

Dry Wall – (AF) EASY FIX® Angle Frame Installation –

Fig. 3

6.1 Drill out the

inner

row of 2mm diameter angle frame pilot holes to 4mm diameter.

6.2 Position the damper centrally in wall opening (width/height), with blades running horizontally. Using

the inner row of pilot holes, screw the EASY FIX® angle frame to the wall using drywall screws @

150mm max pitch.

6.3 It is not a necessity to fill the void behind the angle frame, but suitable fire rated infill may be used if

considered required for insulation purposes.

6.4

Important:

Ensure the screws ‘pick up’ the track lining the hole, so that the proper fire integrity of the

installation will not be compromised.

6.5 On the reverse side, fit a single layer pattress around the damper spigot using drywall screws of

appropriate length to screw into the steel tracking around the opening.

Fig. 3

«
...
2
3
4
5
6
...
»

Содержание BSB FSD-TD Series





















Отзывы:

Нет отзывов