Mahr Maxum III Скачать руководство пользователя страница 27

Страница: 27 / 56

Maxuum III Digital Electronic Indicator 2239028 Rev D

Press and release the Auto-Zero button for final zero setting.
The unit is now in standard measuring mode and ready to gage

parts.

NOTE: Some Mahr gages are furnished with separate instruc-

tions covering their use with Maxum III Indicators. Refer to

those instructions for specific steps for setup and operations.

NOTE: To Save battery life, the gage setup should permit the

Indicator to return to its Sleep Mode when not in use.

4.1.5 Setting Upper and Lower Tolerance Limits

Limits may be set to the resolution of the least digit anywhere

within each model's analog range. Both limits can be set on the

same side (unilateral) of zero or on opposite sides (bilateral) of

zero. Unit must be in Standard Operating Mode for this setting

procedure. Selection cannot be made while in TSP mode.
Any convenient method, such as a height stand or a bench

comparator, may be used to set limits. Once set, limits are

retained in memory, even when the Indicator is in its Sleep

mode, and remain set until changed. If no limits are needed,

move them outside the normally used portion of the measuring

range.

Depress the spindle and press the Left Tolerance Limit

button or press the appropriate display

but-

ton to index the digital readout to the desired lower

limit (-) set point.

Press and release the Left Tolerance Limit

button.

A blinking left arrow appears.

Depress the spindle and press the Right Tolerance Limit

button or press the appropriate display

but-

ton to index the digital readout to the desired upper

limit (+) set point.

Press and release the Right Tolerance Limit

button.

A blinking right arrow appears.

NOTE: To set limits, the measuring spindle must be positioned

within the analog range of the display. To use display buttons,

the Indicator must be in the measuring mode.

NOTE: To check limit settings, use display buttons to index the

fan and digital display through limit set points. Reset limits if

necessary. This can be used to set tolerance value more pre-

cisely. A single press and release of the display button moves

Содержание Maxum III

























































Результаты поиска

Содержание Maxum III

Отзывы:

Похожие инструкции для Maxum III

Бренды по названию

Популярные бренды

Mahr Maxum III, Инструкция по эксплуатации

Результаты поиска

Содержание Maxum III

Отзывы:

Похожие инструкции для Maxum III

Бренды по названию

Популярные бренды