Mahr 3723010 страница 67 Скачать руководство пользователя

Страница: 67 / 88

Mahr GmbH • Millimar C1202

The display shows information on

how to position the probe for the

second measuring point.

–

Use the

key to confirm the value or

to cancel the process.

–

Following successful measurement,

press

to activate the customer

calibration or

to cancel the

process.

An error message appears if the

measured values of the customer

calibration are not plausible.

– Use

to repeat the customer

calibration or

to cancel the

process.

To avoid any measurement errors that may be caused by a previously created

customer calibration, it is advisable to activate the factory standard calibration

again. This is always stored in the measuring instrument and is not changed by the

customer calibrations.

Содержание 3723010

























































































Результаты поиска

Содержание 3723010

Отзывы:

Похожие инструкции для 3723010

Бренды по названию

Популярные бренды

Mahr 3723010, Руководство по эксплуатации

Результаты поиска

Содержание 3723010

Отзывы:

Похожие инструкции для 3723010

Бренды по названию

Популярные бренды