Maguire Products Weigh Scale Blender WSB, Руководство по эксплуатации и техническому обслуживанию

Страница: 43 / 99

M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
43
W E I G H S C A L E B L E N D E R
®
Enter 2 digits to retrieve one of 50 recipes.
Display will flash through this recipe data:
(RCP 01), (1R= xx ), (2N= xx.x), etc., (* = LOAD)
Press "*" to LOAD this recipe into memory.
Routine will exit automatically.
Press RCP or EXIT to return to the display (GET --).
Press RCP or EXIT again to exit.
To SAVE a RECIPE you must be in the PROGRAM mode. If you press RCP key again after display of (GET -
-), display says (SAVE --). Enter 2 digits, display will say (SAVING ). The current settings are saved into
memory under the recipe number you have entered. Routine will EXIT automatically.
EXIT will exit at any time. To clear a recipe, set all component settings to zero and save these settings into the
recipe location.
TAG
- This key allows two pieces of information to be "tagged" onto all data that is either printed or retrieved
through the computer communications ports. The items are WORK ORDER number and OPERATOR
number.
This key is NOT FUNCTIONAL unless the 2nd digit of the "FLG" parameter is set to 1 (x1xxx). To do this, see
the SOFTWARE MAINTENANCE section, PARAMETER TABLE, "FLG".
Press once to display the current Work Order number:
Work Order: xxxxxx
. Press again to display the
current Operator number:
Operator Number: xxx
. Press again for the Recipe number:
Recipe: xxxxx
. You
may enter or change the Work Order or Operator number, when each is displayed to tag all information with
these numbers. The Recipe number is used only for the Recipe Auto Download feature of the G2 software or
the earlier MLAN software. For information on Auto-download see the
Recipe Auto Download
function in the
G2 Software Manual.
Work Order and Operator numbers are for your TRACKING of information ONLY. They have NO EFFECT on
the operation of the Weigh Scale Blender.
•
WORK ORDER
number (6 digits) allows you to tag all information with an internal accounting number
such as a job or purchase order number. To set a work order, enter a number ranging from 1 to
999999, then press SAVE.
•
OPERATOR
number (3 digits) allows you to track who is operating the equipment. To set an operator
number, enter a number ranging from 1 to 999, then press SAVE.
•
RECIPE
number allows you to request a recipe stored in the G2 Software using a recipe number
between 100 and 65536. The Recipe Tag number is not for loading internally stored recipes. See the
RECIPE key for loading internally stored recipe numbers. If a recipe has been entered using our G2
or MLAN software, then a 3-digit or 5-digit number will be displayed in this field. If a new recipe
number is entered and the TAG or EXIT key is pressed, the controller will display:
Waiting for
Recipe…
At this time, the controller is requesting a recipe from the G2 Software using the MLAN
protocol. A matching recipe number found in the G2 Recipe database will then be sent to the
controller, enabling or disabling components and setting settings. G2 will then begin tracking material
usage for that recipe. If the G2 Software does not have a matching recipe number, the controller will
alarm briefly and then revert back to it’s previous loaded recipe. A successfully loaded recipe number
will be displayed and "tagged" to all printouts and retrievals. EXIT will exit the sequence at any point.
Exit will also abort a pending Recipe Auto Download.
Special Alarm Conditions
Enable Alarms
Weigh bin loosing weight –
When enabled, if the weigh bin weight drops more them 20 grams during a cycle
this alarm will sound. This serves to detect and report a weigh bin problem, such as material leaking from the
bottom of the bin.