background image

4 - Operation 

mDynamo| EMV Contact Reader / Transaction Hub Module | Installation and Operation Manual 

 

Page 23 of 27 (

D998200144-14

4.2

 

About the General Status LED 

mDynamo’s on-board General Status LED and the 

External LED Connector [J2]

 can be used to provide 

feedback to operators and cardholders about the internal state of the device (see 

Figure 1-1

).  By default, 

the device drives 

J2

 to match the General Status LED.  However, custom software on the host the device 

is connected to may completely override the External LED behavior. 
 

Table 4-1 

shows how to interpret the colors and flashing patterns of the General Status LED, and the 

behavior of an external LED if the host is not overriding the 

J2

 behavior. 

Table 4-1 – General Status LED Meaning 

Color 

Flashing Pattern 

Meaning 

Off 

Off 

 

The device is not receiving adequate power from 
the host via the USB port. 

Green 

Steady On 

 

The device is ready to read a contact chip card. 

Red 

Steady On 

 

An operator is updating the firmware.  On 
completion, the device will reset and the LED will 
turn off briefly. 

 
 

 

Содержание MDYNAMO




























Отзывы: