Magnum CSW412 Скачать руководство пользователя страница 3

ii 

© 

2015 Sensata Technologies

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains safety instructions that must be followed during the 

installation and operation of this product. Read all instructions and safety 

information on the inverter and in this manual before installing or using.

Safety Symbols

To reduce the risk of electrical shock, 

fi

 re, or other safety hazard, the 

following safety symbols have been placed throughout this manual to 

indicate dangerous situations and important safety instructions.

WARNING:

 Indicates that failure to take a speci

fi

 ed action could 

result in physical harm to the user.

CAUTION:

 Indicates that failure to take a speci

fi

 ed action could result 

in damage to the equipment.

Info:

 Indicates information that emphasizes or supplements important 

points of the main text.

Product Safety Warnings

WARNINGS: 

Failure to follow the instructions below and in this 

manual can result in death or serious injury.

• 

All electrical work must be performed in accordance with local, state and 

federal electric codes.

•  This product is designed for indoor/compartment installation. Do not 

expose to rain, snow, moisture, or liquids of any type.

• 

Use insulated tools to reduce the chance of electrical shock or accidental 

short circuits. Be sure to remove all jewelry such as rings, watches, 

bracelets, etc., when installing or performing maintenance on the inverter.

• 

Always disconnect the batteries or energy source prior to installing or 

performing maintenance on the inverter. Live power may be present at 

more than one point since an inverter utilizes both batteries and AC.

• 

Do not cover or obstruct any air vent openings and/or install in a zero-

clearance compartment - always operate unit in an open area.

•  When working with electrical equipment or lead acid batteries, have 

someone nearby in case of an emergency.

• 

Study and follow all the battery manufacturer’s speci

fi

 c precautions when 

installing, using, and servicing the battery connected to the inverter.

• 

While working with batteries, wear eye protection and gloves, and avoid 

touching your eyes. Keep fresh water and soap on hand in the event battery 

acid comes in contact with eyes. If this occurs, cleanse right away with soap 

and water for a minimum of 15 minutes and seek medical attention.

• 

Batteries produce explosive gases, DO NOT smoke or have an open spark 

or 

fi

 re near the system.

• 

Avoid dropping any metal tool or object on the battery. Doing so could 

create a spark or short circuit which goes through the battery or another 

electrical tool and may cause an explosion.

• 

Shock Hazard! Keep away from children!

• 

These inverters provide household AC, treat the AC output sockets the 

same as regular wall AC sockets at home.

• 

Explosion hazard! DO NOT use this inverter in the vicinity of 

fl

 ammable 

fumes or gases (such as propane tanks or large engines).

•  These inverters contain no user-serviceable parts. See the Warranty 

section for how to handle service issues.

Содержание CSW412































Отзывы: