Magnum 261815 страница 57 Скачать руководство пользователя | Manualshive

Страница: 57 / 84

background image

Motor Diagnostics (X5 and X7)

312667H

25

Motor Diagnostics (X5 and X7)

If Motor Diagnostics reveal a damaged motor or if motor brushes are shorter than 1/4 in. (6.4 mm) replace the motor
using Motor Kit, page 28.

Setup

1.

Unplug power cord and Relieve Pressure, page 11.

2.

Remove enclosure and disconnect two black motor
leads to control board (see Wiring Diagram, page
46).

3.

Remove motor fan cover by gently prying up on
retention tabs on sides of motor. Motor shaft should
spin easily when turning fan. If motor shaft does not
turn easily, there is a problem with pump, gears, or
motor (see Troubleshooting, page 13).

4.

Inspect motor windings for evidence of overheating. If
windings appear burnt and motor smells, replace
motor.

5.

Use Ohmmeter to measure resistance across two
black motor leads. Resistance of motor should fall
within range of 1.5 to 4.5 ohms. If motor falls outside
resistance range or is open circuit, replace motor.

6.

Use Ohmmeter to measure resistance of motor leads
to motor laminations. If resistance is not open circuit,
replace motor.

7.

Inspect length of both brushes by looking at brush
torsion spring. If spring is not bottomed out in slot for
brush spring, brush length is acceptable. If brushes
are worn out, replace motor.

Motor Diagnostics (ProX7 and ProX9)

Check for electrical continuity in motor armature, windings and brush as follows:

If Motor Diagnostics reveal a damaged motor or if motor brushes are shorter than 1/4 in. (6.4 mm) or if the motor shaft
cannot turn, replace the motor using Motor Kit, page 28.

Setup

1.

Relieve Pressure, page 11.

2.

Unplug electric cord.

3.

Remove enclosure and disconnect motor leads from
control card.

4.

Remove fan brace.

5.

Remove four screws and front cover.

6.

Remove yoke and guide rods.

7.

Remove gear.

Armature Short Circuit Spin Test

Quickly turn motor fan by hand. There should not be
electrical shorts and fan should coast two or three
revolutions before stopping. If fan does not spin freely,
armature is shorted. Replace motor using Motor Kit,
page 28.

Armature, Brushes and Motor Wiring Open Circuit
Test (Continuity)

1.

Connect red and black motor leads together with test
lead.

2.

Turn motor fan by hand, about two revolutions per
second.

3.

If there is an uneven resistance or no resistance,
replace motor using Motor Kit, page 28.

«
...
55
56
57
58
59
...
»

Содержание 261815





















































































Отзывы:

Нет отзывов

Похожие инструкции для 261815

Бренд: Pattfield Страницы: 92

Бренд: Keeper Страницы: 28

Бренд: Fountainhead Страницы: 20

Бренд: GUSMER Страницы: 28

Бренд: Graco Страницы: 12

Бренд: C.A. Technologies Страницы: 4

Бренд: Carlisle Страницы: 4

Бренд: YEAZ Страницы: 52

Бренд: Black & Decker Страницы: 27

Бренд: Black & Decker Страницы: 36

Бренд: F/S Страницы: 4

Pakblast 50 Gal

Бренд: Rears Страницы: 58

Бренд: WAGNER Страницы: 3

Бренд: Briggs & Stratton Страницы: 9

Бренд: Larius Страницы: 46

Бренд: ParkerBrand Страницы: 11

Бренд: Graco Страницы: 56

Бренд: 3M Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды