background image

Component Identification

312082B

5

Component Identification

Project Painter 7

A

AllControl

 

STORAGE: for long term and overnight shutdown and storage.

OFF: turns motor off for short term shutdown and relieves system 
pressure.

PRIME/CLEAN PUMP: turns on motor and directs fluid to prime 
tube.

ROLL: directs low pressure fluid to roller (when used)

PRIME/CLEAN GUN & HOSE: directs fluid to gun and hose.

LOW SPRAY to HIGH SPRAY: directs fluid to spray gun.

B

Pump fluid outlet fitting

Threaded connection for paint hose.

C

Suction tube

Draws fluid from paint pail into pump.

D

Prime tube (with diffuser)

Drains fluid in system during priming and pressure relief.

E

Inlet screen

Prevents debris from entering pump.

F

Pail hanger

For transporting pail by its handle.

G

Roller tray/Gun holder/Hose Wrap

Removable tray can also be used to clean paint roller. 

H

Quick Release Latch

Collapses handle for compact or hanging storage.

J

Storage compartment

Provides onboard storage for spray tips and/or tools.

L

Sample spray shield

Introduces benefits of a spray shield. Blocks paint from surfaces you do 
not want to spray.

M

SpillGuard

 tray

Protective tray to set sprayer and paint pail on during operation.

N

Practice spray board

Instructs user on how to perform basic spraying techniques and provides 
surface to practice techniques prior to spraying surfaces.

P

Power Flush

 attachment

Connects garden hose to Suction tube for power flushing water-base 
fluids.

R

Paint hose

Transports high-pressure fluid from pump to spray gun.

S

Airless spray gun

Dispenses fluid.

T

Tip guard

Reduces risk of fluid injection injury.

U

Reversible spray tip

Atomizes fluid being sprayed, forms spray pattern and controls fluid 
flow according to hole size.

When reversed, unclogs plugged tips without disassembly.

V

Gun fluid filter

Filters fluid entering spray gun to reduce tip clogs.

W

Roller attachment

Attaches to spray gun for pressure rolling directly on surfaces.

X

Gun trigger safety lever (page 7)

Prevents accidental triggering of spray gun.

Содержание 261805





























Отзывы: