manualshive.com logo in svg

Magnum 232735, Руководство по ремонту и запасным частям

Поделиться
Скачать
Magnum 232735 Скачать руководство пользователя страница 20

Advanced Troubleshooting 

20

309226M

Control board is damaged.

CAUTION: 

Do not perform 

control board diagnostics until 
you have determined the 
armature is good. A bad motor 
can burn out a good control 
board.

See 

Control Board Diagnostics

, page 25. If 

damaged replace control board using 

Control 

Board Kit

, page 22.

Motor runs and pump cycles, 
but pressure does not build up.

Intake valve ball or outlet valve 
ball is not seating properly.

Remove and clean valves and check balls and 
seats for nicks; replace if necessary. Strain paint 
before spraying to remove particles that could clog 
pump. 

Pump Service

, page 25.

Pump packings are worn or 
damaged.

Check for leaking around throat packing nut. 
Replace pump packings if there are leaks. 

Pump 

Service

, page 25.

Prime/Spray Valve leaking.

Check Prime/Spray Valve for debris trapped on 
seat and for worn parts. Torque to 185 in-lb (21 
N•m). If parts are worn, replace valve using 

Prime/Spray Drain Valve Kit

, page 22.

Spray pattern has variations, 
pressure fluctuates 
excessively, or motor runs very 
slowly.

Leads from motor or pressure 
switch to control board are 
damaged, loose or overheated

Be sure terminals are centered and firmly 
connected. Inspect wiring insulation and terminals 
for signs of overheating. Replace any loose 
terminals or damaged wiring. Securely reconnect 
terminals.

Pressure control switch leads 
are pinched between pump 
and drive housing or between 
front cover and drive housing 
(XR models only)

Make sure pressure control harness is routed 
behind pump, through retention clip and 
connected to control board connector on control 
board (connect with tab to right). 

Control board is damaged.

CAUTION: 

Do not perform 

control board diagnostics until 
you have determined the 
armature is good. A bad 
armature can burn out a good 
control board.

See 

Control Board Diagnostics

, page 25. If 

damaged, replace control board using 

Control 

Board Kit

, page 22.

Pressure control switch is 
damaged or worn out.

Replace pressure control switch using 

Pressure 

Control Switch Kit

, page 22.

Specific Problem

Cause

Solution

Содержание 232735









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды