manualshive.com logo in svg

Magnum 232735, Руководство по ремонту и запасным частям

Поделиться
Скачать
Magnum 232735 Скачать руководство пользователя страница 13

Basic Troubleshooting

309226M

13

Pump cycles but does not build up 
pressure.

Pump is not primed.

Prime pump.

Inlet screen (L) is clogged or suction 
tube (G) is not immersed.

Clean debris off inlet screen and 
make sure suction tube is at bottom 
of paint pail.

Paint pail is empty.

Refill paint pail. Reprime sprayer.

Suction tube is leaking.

Tighten suction tube connection (K). 
Inspect for cracks or vacuum leaks.

Pump check valves are dirty or dam-
aged. (Usually only one valve).

Clean or replace check valves. See 

Pump Service

 on page 25.

Spray-Prime/Drain Valve (J) is worn 
or obstructed with debris.

Check Spray-Prime/Drain valve for 
debris trapped on seat or worn parts. 
Torque to 185 in-lbs (21 N•m). 
Replace if parts are worn.

Pump cycles, but paint only dribbles 
or spurts when spray gun is trig-
gered.

Pressure is set too low.

Slowly turn Pressure Control Knob 
(C) clockwise to increase pressure 
setting and verify if sprayer pressure 
increases.

Spray tip is clogged.

Unclog spray tip. See Operation Man-
ual 309225.

InstaClean fluid filter is clogged (XR 
models only).

Clean or replace InstaClean fluid fil-
ter (E).

Spray gun fluid filter is clogged or 
installed backward.

Clean or replace gun fluid filter (V).

Spray pattern is inconsistent or is 
leaving stripes.

Pressure is set too low.

Turn Pressure Control Knob (C) 
clockwise, to increase pressure.

Spray tip is worn beyond capability of 
sprayer.

Replace spray tip.

Pressure is set at maximum but 
cannot achieve a good spray pattern.

Spray tip is too large for sprayer.

Select smaller spray tip.

Spray tip is worn beyond capability of 
sprayer.

Replace spray tip.

Extension cord is too long or not 
heavy enough gauge.

Replace extension cord. 

Grounding 

and Electrical Requirements

, page 

6.

Spray gun fluid filter is clogged.

Clean or replace spray gun fluid filter.

InstaClean fluid filter is clogged (XR 
models only).

Clean or replace InstaClean fluid 
filter.

Inlet screen is clogged.

Clean debris off inlet screen.

Pump valves are worn.

See 

Low or Fluctuating Output

, 

page 19.

Problem

Cause

Solution

Содержание 232735









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды