background image

 

51

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

AMERICAN ENERGY SYSTEMS INC. LIMITED PRODUCT 

WARRANTY 

 

This warranty is in effect on all products sold after 01/01/2009 and supersedes any and all warranties currently in 

existence. 

Please keep a copy of this warranty for your personal records or in the event of a claim 

 

American Energy Systems Inc., hereinafter referred to as (AES), warrants to you, the original consumer purchaser, that 
this product is free from defects in material and workmanship for a period of five (5) years from the original purchase date 
minus any time past one (1) year from manufacturing date, and that the product’s electrical parts and steel firepot, are free 
from defects in material and workmanship for a period of one (1) year from the original consumer purchase date minus 
any time past one (1) year from manufacturing date, and that the cast iron firepot models carry a lifetime warranty against 
defect in material or workmanship (excluding war page or deterioration), and that door glass carries a lifetime 
replacement warranty against heat breakage (does not cover accidental breakage) . There is expressly no warranty on  
installation of product, any venting, grates, gaskets, door latches, insulation, ceramic or brick boards/logs/backing, paint, 
plated surfaces/doors/trims, baffles, bushings, bearings, auger flightings, war page or discoloration of steel or plated parts 
or any other normal wearing part. In the event the product fails to conform to this warranty, AES, through the place where 
you purchased the product or if purchased on the AES E-Com store directly through AES, will provide the parts and 
components necessary to remedy such nonconformity. 

AES will not be responsible for any labor, mileage or freight 

cost to the factory under this warranty. 

This warranty is not transferable. 

 

In order to obtain performance under this warranty, you must (1) have registered this warranty within 30 days of purchase 
by completing and returning the warranty registration card or filling in the on-line warranty registration form at 
www.magnumheat.com, and (2) promptly report the claimed nonconformity to your  place of purchase, also providing 
your name, address, phone number, proof of purchase, date of purchase, the model and serial number of the stove, digital 
pictures of installation and venting inside and outside of the home, pictures of the claimed nonconformity part and the 
claimed nonconformity. 

All claims must be submitted in writing to your place of purchase. 

 

AES shall have no warranty obligations if this product; (1) was not purchased from an authorized AES dealer; (2) was not 
installed by a AES dealer or other qualified installer; does not have outside combustion air hooked directly to the unit; (3) 
was not operated and maintained in strict accordance with the manufacturer’s instructions, local or national codes or (4) 
was subject to abuse, misuse, negligence or accident. AES shall have no warranty obligation for damage caused by 
improper handling, freight damage (must be reported to freight provider), over-firing, unapproved fuel, variance in feed 
rates, variances in BTU output or the unauthorized disassembly or modification of the product. AES shall have no 
warranty obligation if this warranty is not timely registered, for claims which are not submitted through the selling AES 
dealer, or for claims submitted verbally or without the required information and documentation. 

 

Before exercising this warranty, an AES representative (the place where the product was purchased or AES approved 
person) must inspect the part/unit to determine if the part/unit is defective.  If a local AES representative is not available 
the original purchaser of the product must submit digital pictures of the part/unit, installation of the unit to AES at 

[email protected]

 If the inspection reveals that the failure is due to defective material or workmanship and the 

part is covered by the conditions of this warranty, AES will, at its option, repair the defective part/unit.  The sole duty of 
AES and liability under this warranty is limited to the repair of the covered defective part/unit.  The purchaser shall 
assume all costs related to shipping the replacement parts or return of the unit to the factory for repairs.  If it is determined 
that the defect was caused by AES, AES will cover the costs of shipping the repaired part/unit to an AES approved 
shipping point.  AES will not cover additional freight or delivery services such as residence delivery charges, special 
handling, etc. 

 

INSTALLATION, VENTING, REMOVAL OR REINSTALLATION COSTS ARE NOT COVERED BY THIS 

WARRANTY.  

 

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THE PRODUCT.  
ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, 
ARE DISCLAIMED.  IT IS UNDERSTOOD AND AGREED THAT AES’S LIABILITY UNDER THIS 
WARRANTY SHALL BE LIMITED TO THE PROVISION OF REPLACEMENT PARTS AND SHALL 
NOT INCLUDE LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.  ANY 
ACTION BROUGHT UNDER THIS WARRANTY MUST BE BROUGHT WITHIN ONE YEAR OF THE 
ACCRUAL OF THE CAUSE OF ACTION AND MAY ONLY BE BROUGHT IN THE CIRCUIT COURT 
OF MCCLOUD COUNTY, MINNESOTA. 

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential 
damage, so the above limitations may not apply to you.  This warranty gives you specific legal rights, and you may also have other 
rights which vary from state to state. 

Содержание WINACP





















































Отзывы: