manualshive.com logo in svg

Magnum Dimensions CSW2012-X, Руководство пользователя, Страница: 39 / 46

Поделиться
Скачать
Magnum Dimensions CSW2012-X Скачать руководство пользователя страница 39

34 

© 

2015 Sensata Technologies

4.0 Troubleshooting

Problem

Possible Cause/

Condition

Solution

The input 

battery under-

voltage warning 

(E05) and/or 

shutdown alarm 

(E01) occurs 

in advance 

even when the 

battery voltage 

seems to be 

OK. (Cont.)

Make sure to measure 

the battery voltage 

just before the 

E01 battery under-

voltage shutdown in 

Battery (Inverter) 

mode occurs, and 

compare it with the 

corresponding voltage 

threshold in the 

speci

fi

 cations table 

(allow +/- 5% of 

tolerance).

Just after the E01 occurs, 

the battery voltage rapidly 

increases since the battery 

is not under a load condition 

after the inverter shutdown. 

This is normal in all the 

battery banks and can 

confuse the user thinking the 

under-voltage shutdown that 

triggers the E02 alarm occurs 

in advance at higher voltage 

thresholds than the ones 

speci

fi

 ed.

The E05 warning and 

E01 shutdown alarm 

occurs well in advance 

due to the SdH 

setting.

If you want to extend the run 

time of the battery bank as 

much as possible without the 

need to keep enough battery 

state of charge for engine 

cranking purposes, make 

sure to set the under-voltage 

shutdown threshold to a low 

values setting (SdL = factory 

default setting) other than the 

SdH.

Содержание CSW2012-X















































Отзывы:

Нет отзывов