Magnum Dimensions CSW2012-X Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 46

Magnum Dimensions CSW2012-X Скачать руководство пользователя страница 27

22

©

2015 Sensata Technologies

2.0 Installation

2.5.6 Removing the Display Panel

The display panel on the inverter can be removed and installed in a different

location using a longer 6-pin standard telephony cable (also referred to as a

RJ12 cable). See Figure 2-8.
• Remove the 2 screws at the front of the display panel, and then

disconnect the small cable from the inverter.

•

Install the remote cable in your desired location and connect one end of

the remote cable to the inverter and the other end of the cable to the

display panel. Please note polarity.

Remote cable

To locate the display panel in a remote location, the longer cable needs

to be a 6-conductor telephony type with 6P6C (6-position/6-conductor)

connectors on each end. With this cable, when the 6P6C connectors are held

side by side with both of the connector tabs facing the same way, the color

of the conductors in each connector are the opposite from top to bottom as

shown in Figure 2-8.

Figure 2-8, Remote Cable

12

3

4

12

3

4

TAB

TAB

same color

same

color

6-conductor telephony type

opposite colors top to bottom

(tabs facing toward you)

«
...
25
26
27
28
29
...
»

Содержание CSW2012-X















































Отзывы:

Нет отзывов