Magnetic Autocontrol MAGSTOP MBE35 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 58

Magnetic Autocontrol MAGSTOP MBE35 Скачать руководство пользователя страница 5

Operation Instructions

MBE35_50 OPERATION MANUAL 2005_10

- 5 -

1.2 General safety information

The MAGSTOP barrier system has been designed, built and tested using state-of-the-
art technology and left our factory only after passing stringent safety and reliability
criteria. Nevertheless, the barrier system can represent a risk to persons and property
if it is not installed and operated correctly. These operating instructions must therefore
be read in their entirety and all safety information contained therein must be complied
with.
The manufacturer shall refuse to accept liability and shall withdraw warranty if this
barrier system is used incorrectly or is used for a purpose for which it was not
intended.

1.3 Intended use

The MAGSTOP MBE 35/50 barriers are designed to control vehicular (see
pictogram below) access and exits to car parks, car parking garages, access
control applications and highways.

The MAGTRONIC control units have been specially designed for controlling Magnetic
barriers.
Any other use of these barrier systems is not permitted.
Modifications or changes to the barrier or to the control modules are prohibited.
Only original Magnetic spare parts and accessories shall be used.

1.4 Warning and safety signage

The Magnetic Automation Corp. MIB barriers come with two (2) safety-warning labels

(see Figure 1 above) that must be applied to the barrier housing so it can easily be
seen when a pedestrian, bicycle users, or motorized vehicle uses the lane. Magnetic
Automation Corp. requires that you use universally identifiable pictograms in all
entrance/exit lanes, roadways, post, and walls. It is strongly recommended to paint a
“NO PEDESTRIAN” pictogram on the roadway immediately adjacent to the parking
barrier gate.

Figure 1

«
...
3
4
5
6
7
...
»

Содержание MAGSTOP MBE35



























































Отзывы:

Нет отзывов