manualshive.com logo in svg
background image

 

January 2011 

3 of 9 

Impulse•G+/VG+ Series

 

Safe-Off 8001.x 

  

PN: 

140-10305 

 

DANGER

WARNING

CAUTION

, and 

NOTE 

Statements

 

 

DANGER, WARNING, CAUTION, 

and 

Note 

statements may be used in this manual to 

emphasize important and critical information. You must read these statements to help ensure 
safety and to prevent product damage. 

 

 

DANGER

 

indicates an imminently hazardous situation which, if not avoided, will result in 

death or serious injury. This signal word is to be limited to the most extreme situations.

 

 

 

WARNING

 

indicates a potentially hazardous situation which, if not avoided, could result in 

death or serious injury.

 

 

 

CAUTION

 

indicates a potentially hazardous situation which, if not avoided, could result in 

minor or moderate injury. It may also be used to alert against unsafe practices. 

 

 

NOTE

A NOTE statement is used to notify of installation, operation, programming, or maintenance 

information that is important, but not hazard-related.

 

 

 

WARNING 

Improper programming of a drive can lead to unexpected, undesirable, or unsafe operation or 
performance of the drive. 

 

Disclaimer of Warranty 

 
Magnetek, hereafter referred to as Company, assumes no responsibility for improper 
programming of a drive by untrained personnel. A drive should only be programmed by a 
trained technician who has read and understands the contents of this manual. Improper 
programming of a drive can lead to unexpected, undesirable, or unsafe operation or 
performance of the drive. This may result in damage to equipment or personal injury. Company 
shall not be liable for economic loss, property damage, or other consequential damages or 
physical injury sustained by the purchaser or by any third party as a result of such programming. 
Company neither assumes nor authorizes any other person to assume for Company any other 
liability in connection with the sale or use of this product. 

 
 

Содержание IMPULSE G+ Series 3










Отзывы: