background image

 

Flex Pro Tethered Controller 

 Instruction Manual 

July 2011 

4 of 17 

2. Remote Controlled Safety 

 

WARNINGS and CAUTIONS 

 

    Throughout this document WARNING and CAUTION statements have been deliberately placed to highlight items 

critical to the protection of personnel and equipment.

 

 

WARNING – A warning highlights an essential operating or maintenance procedure, practice, etc. which if 
not strictly observed, could result in injury or death of personnel, or long term physical hazards. Warnings 
are highlighted as shown below: 

  

WARNING

 

 

CAUTION – A caution highlights an essential operating or maintenance procedure, practice, etc. which if not 
strictly observed, could result in damage to, or destruction of equipment, or loss of functional effectiveness. 
Cautions are highlighted as shown below: 

  

CAUTION 

 

 

WARNINGS and CAUTIONS SHOULD NEVER BE DISREGARDED.

 

The safety rules in this section are not intended to replace any rules or regulations of any applicable local, state, or 
federal governing organizations. Always follow your local lockout and tagout procedure when maintaining any radio 
equipment. The following information is intended to be used in conjunction with other rules or regulations already in 
existence. It is important to read all of the safety information contained in this section before installing or operating the 
Remote Control System. 

Содержание Flex Pro Tethered Controller






















Отзывы: