Magnavox MWC13D5 A, Руководство по обслуживанию

Страница: 17 / 71

1-5-1 T8100DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
Caution !
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
2. Disassembly Method
(1): Order of steps in Procedure. When reassembling,
follow the steps in reverse order.These numbers
are also used as the Identification (location) No. of
parts in Figures.
(2): Parts to be removed or installed.
(3): Fig. No. showing Procedure of Part Location.
(4): Identification of part to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
S=Screw, P=Spring, L=Locking Tab, CN=Connec-
tor, *=Unhook, Unlock, Release, Unplug, or
Desolder
2(S-2) = two Screws (S-2)
(5): Refer to the following "Reference Notes in the
Table."
Reference Notes in the Table
Caution !
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
CAUTION 1: Discharge the Anode Lead of the CRT
with the CRT Ground Wire before removing the Anode
Cap.
1. Disconnect the following: Anode Cap, CN1801,
CN1802, CN2505, CRT CBA, CN1601 and
CN1571.
Then remove Tray Chassis Unit.
CAUTION 2: Electrostatic breakdown of the laser
diode in the optical system block may occur as a
potential difference caused by electrostatic charge
accumulated on cloth, human body etc., during
unpacking or repair work.
To avoid damage of pickup follow next procedures.
2-1. Disconnect Connector (CN9301) on the Main
CBA Unit.
2-2. Remove four Screws (S-5) and lift the DVD
Mechanism up. (Fig. 3)
2-3. Short the three short lands of FPC cable with
solder before removing the FFC cable (CN201)
from it. If you disconnect the FFC cable (CN201),
the laser diode of pickup will be destroyed. (Fig.
4)
2-4. Remove three Screws (S-6) and Loader Cover.
CAUTION 3: When reassembling, confirm the FFC
cable (CN201) is connected completely. Then remove
the solder from the three short lands of FPC cable.
(Fig. 4)
ID/
LOC.
No.
PART
REMOVAL
Fig.
No.
REMOVE/
*UNHOOK/UNLOCK/
RELEASE/UNPLUG/
DESOLDER
Note
[1]
Rear
Cabinet
1 4(S-1), (S-2), 2(S-3) -
[2]
Tray
Chassis
Unit
2,3,
5
Anode Cap, CN1801,
CN1802, CN2505,
CRT CBA, CN1601,
CN1571
1
[3] CRT 2 4(S-4) -
[4]
DVD
Mechanism 3,4,
5
4(S-5), 3(S-6),
Loader Cover,
CN201, CN9301
2-1
2-2
2-3
2-4
3
[5]
DVD Main
CBA Unit
3,5
(S-7), Loader PCB
Holder, CN1 (CN2),
CN3 (CN4)
-
[6] Main CBA 3 4(S-8) -
↓
(1)
↓
(2)
↓
(3)
↓
(4)
↓
(5)
[1] Rear Cabinet
[2] Tray Chassis Unit [3] CRT
[4] DVD Mechanism
[5] DVD Main CBA Unit
[6] Main CBA