OR
ANT.IN
OR
UHF
VHF
300
Ω
75-300
Ω
AD
APTO
R
ANT.IN
H
OOKING
U
P
Y
OUR
TV (A
NTENNA
/C
ABLE
C
ONNECTIONS
)
A
combination antenna
receives normal broadcast
channels (VHF 2-13 and UHF
14-69). Your connection is easy
since there is only one 75
Ω
(ohm) antenna jack on the
back of your TV - and that’s
where the antenna goes.
A
NTENNA
C
OMBINATION
UHF/VHF
To set the
TV to select only
the channel num-
bers in your area,
see Auto Install
(page 3).
S
MART
H
ELP
If your antenna has a
round connector (75
Ω
),
then you're ready to connect it
to the TV. Go to step 2.
If your antenna has flat
twin-lead wire (300
Ω
), you
first need to attach the antenna
wires to the screws on a 300
to 75
Ω
adaptor (not supplied).
Push the round end of
the adaptor (or cable) onto
the ANT(enna) IN jack on
the back of the TV. If the
round end of the adaptor or
cable is threaded, screw it
down tight.
Y
ou may have two separate
antennas. One antenna is
for VHF channels (2-13) and
the other antenna is for UHF
channels (14-69).
For homes with separate
UHF/VHF antennas, you will
need an optional combiner
before you can connect the
antennas to the TV.
S
EPARATE
UHF/VHF
300 to 75
Ω
Adaptor
Combination
VHF/UHF
Antenna
(Outdoor or
Indoor)
Twin-lead
Wire
Round Cable
75
Ω
Back of TV
Back of TV
UHF/VHF
Combiner
75-300
Ω
Adaptor
Outdoor UHF Antenna
(Twin-lead 300
Ω
)
Outdoor VHF
Antenna
(Twin-lead 300
Ω
)
Twin-lead
Wire
Push the round end of the
combiner onto the ANT(enna)
IN jack on the back of the TV.
Attach the separate
UHF and VHF antennas to
the correct screws on the
combiner (not supplied).
Round
End
Outdoor VHF
Antenna
(Round cable 75
Ω
)
- 2 -
IN
OUT
OR
ANT.IN
Y
our Cable TV signal may be
a single (75
Ω
) cable or a
Cable Box installation. In either
case, the connection to the TV
is very easy.
C
ABLE
TV
C
ABLE
/C
ABLE
B
OX
If you do not have a
Cable Box, then you're ready
to connect your Cable TV sig-
nal to the TV. Go to step 2.
If you have a Cable Box:
Connect the Cable TV signal
to the IN jack on the Cable
Box.
If you do not have a
Cable Box, connect the Cable
TV signal directly to the
ANT(enna) IN jack on the TV.
If you have a Cable Box:
Use a coaxial cable (not sup-
plied) to connect the OUT jack
of the Cable Box to the
ANT(enna) IN jack on the TV.
Back of TV
Coaxial cable
Cable Box
To select
only the channels on
your Cable system,
see Auto Install
(page 3).
If you use a Cable
Box, set the TV to
the same channel as
the CH 3/4 switch
on the back of the
Cable Box. Select
channels at the
Cable Box.
S
MART
H
ELP
Cable TV Company
Cable TV Signal (75
Ω
)
Note to the Cable TV System Installer: This reminder is provided to call the Cable TV system
installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for
proper grounding - in particular, specifying that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as possible.
