background image

7

USING GRILL WITH CNG (NATURAL GAS) SYSTEMS

• Magma on-board CNG (natural gas) valves allow Magma grills to be installed to an existing on-board, pre-regulated low 

pressure CNG (natural gas) system.

• Use only Magma Type 4 Low Pressure CNG (natural gas) control valves. Visit out website at 

MagmaProducts.com

 to view 

valve application guide. See your local dealer for proper hose and fittings.

Problem

Electrode covered with grease or residue
Igniter/electrode too far from burner 

Electrode wire loose, disconnected, or corroded  

Wire is shorted causing spark from wire before 
electrode
No spark being generated 

 
 
 

No gas flow
 
Obstructed gas flow 

Excessive cooking temperature

Grease and/or residue build-up
Excessive fat in meats
Excessive oils in marinades
Obstructed gas flow

Flame too low 
Wind directly on burner
Obstructed gas flow

Grill not level
Grease or residue build-up
Excessive fat in meats
Excessive oil in marinades

Clean electrode
Adjust electrode until proper spark appears  
(see page 5)
Clean, adjust & reconnect wire between igniter 
& electrode, see Complete Disassembly (page 5)
Replace Igniter, Electrode & Wire 
See website for part number
Adjust electrode until proper spark appears.
Unscrew igniter push button, remove/inspect 
“AAA” battery, replace “AAA” alkaline battery if 
necessary, reinstall & re-assemble push button
Replace Igniter, Electrode & Wire 
See website for part number
Check fuel level, replace canister or  
refill cylinder
Clean burner and valve orifice.  
Remove debris/spider webs
Operate only on low when lid is closed
Reduce flame level
Leave lid open
Use water spray to cool
Clean components
Trim fat from cuts of meat before grilling
Use non-oil based marinades
Clean burner and valve orifice. 
Remove debris/spider webs
Increase flame
Block wind when opening lid
Clean burner and valve orifice. 
Remove debris/spider webs
Level Grill
Clean components
Trim fat from cuts of meat before grilling
Use non-oil based marinades

Hot Spots

Blow-out

Yellow sooty 

flame

Flare-up

Burner will    

not light even 

with match

Burner will    

not light with 

igniter

TROUBLE SHOOTING GUIDE

Possible Solution

Possible Cause

7

Содержание C10-601T-CSA









Отзывы: