6
MAINTENANCE
Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture.
It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a
protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface
rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry.
Avoid using stainless steel polishes on grill exterior as most leave a residue that may discolor when grill is heated.
Additionally, stainless steel that is exposed to high heat will change color and texture over time. The “amber” color of
grill exterior and internal components is not a failure of the stainless steel and will not affect products operation. When this
happens, we recommend using
“Magma Magic” Grill Restorer
to remove the “amber” color and return grill to its original
luster. However, prolonged exposure to extreme high heat will cause chromium and nickel to “burn out” of stainless steel. At
this point stainless steel will become more susceptible to corrosion and will start to deteriorate. We recommended
replacement of internal components as they become seriously deteriorated.
We recommend thoroughly cleaning grill and internal components after each outing. Disassemble interior components
and remove all food residue. Use a “Scotch Brite” pad or similar product and “Easy-Off” oven cleaner for cleaning grills
interior components, followed by thoroughly washing with soap and water, rinse with fresh water & dry. AVOID CONTACT
OF OVEN CLEANER WITH SKIN, CONTROL VALVE, IGNITOR ELECTRODE & WIRE, AND BOAT SURFACE. CAUTION: DO NOT
USE ANY TYPE OF ABRASIVE PAD ON EXTERIOR MIRROR FINISH AS IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH.
We recommend covering grill between uses. Grill covers are available at Magma retailers or directly from Magma.
Grill Grates
-
Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with
soapy water and dry prior to storage.
Ceramic Electrode
-
Located just beside the burner, it should be kept clean of grease and debris. Be careful not to
damage the ceramic insulation or the wire. See page 5 for electrode spark adjustment.
Control Valve
-
All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way.
Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the orifice.
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
Propane (LPG)
Gas Regulator
A10-225 LPG (Propane)
10' Gas Grill Connection Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gourmet
Gas Grill
Type 3
Valve
Solenoid
Typical Marine &
R.V. Application
Gourmet
Gas Grill
Align valve stem key
to valve chamber
lock detent and rotate
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
s-AGMA/N"OARD,0'0ROPANE 6ALVES
Hose Kits allow Magma Grills to be installed
within a boats existing on-board, pre-regulated
LOWPRESSURE,0'0ROPANE SYSTEM
s5SEONLY
Magma Type 3 Low Pressure LPG
(Propane) Valves.
s)N.ORTH!MERICAUSE
Magma A10-225 LPG 10'
Gas Grill Connection Kit
in conjunction with
Type 3 Valve.
Outside North America check
your local dealer for proper hose and fittings.
s!PRIMARYSHUTOFFVALVE
(supplied with Gas
Grill Connection Kit)
must be used with this
control valve at point of connection into your
system. This allows shut off of gas supply to hose
leading to grill.
s
In Australia & New Zealand LPG fuel
systems must be installed by a certified
gas technician.
