background image

 

1-800-MAGLINE 

(624-5463) 

                                             www.magliner.com

15

Switch - Up/Down  (includes wiring harness)

534416

Timing belt - 5mm pitch x 15mm W x 60 grooves

534118

Top cover assembly

533502

Trolley assembly

531700

Wiring harness for lower limit switch

64079

Wiring harness for upper limit switch

534401

Wiring harness for negative power (ground)

64077

Wiring harness for positive power

64078

Wiring harness for positive power to control board

64078

Wiring harness - adapter for motor solenoid

534421

Wiring harness/connector assembly for remote control input

534409

Wiring harness/connector assembly for power jack (charger input)

534408

Wiring harness for green charging light

534411

Wiring harness for red overload light

534412

Chassis Parts

Part 

Number

Chassis assembly, standard caster

530124

Chassis assembly, caster with brakes

530110

Axle, 10” wheels

532311

Axle spring pin

190104

Axle cotter pin

81077

Locking pin - 1/2” x 5/8” with lanyard

81194

Caster - 3-1/2” dia. x 1-1/4” wide

130034

Caster with brake - 3-1/2” dia. x 1-1/4” wide

130035

Floor brake

33051

Plug for round tube

530115

Plug for square tube

530123

Washer, thick - 5/8”

80705

Washer, thin - 5/8” x 1/32”

80707

Wheel - 1075 microcellular foam, HDPE hub - 10” x 2-3/4”

111075

Motor assembly - standard speed (includes motor, mounting bracket, 

solenoid,brake, pulley #1, pulley #2-3, and timing belt)

534100

Motor cover

533505

Nut, trolley drive

531705

Pin for quick change latch

81169

Pulley assembly #1  (top gear)

534106

Pulley assembly #2-3  (intermediate)

534107

Pulley assembly #4  (lower)(part of 531121 lift screw assembly)

531117

Side plate assembly with quick change latch

536034

Switch - On/Off  (includes wiring harness)

534410

Содержание LiftPlus Lite

















Отзывы: