background image

 

1-800-MAGLINE 

(624-5463) 

                                             www.magliner.com

13

Troubleshooting Guide

Problem

Solution(s)

The lift does not respond, and does 

not make any noise when the lift 

switch is activated.

1. Is the power switch turned on?

2. Has the circuit breaker tripped?

3. Check the battery connections.

4. Recharge the battery.

5. Replace the battery.

The lift struggles to raise objects and 

works very slowly.

1. Check for dirt or other obstruction around the lift screw.

2. Recharge the battery.

3. Replace the battery.

The lift will not rise for more than a 

second, but it will lower.

1. If the red light is on, you may have exceeded the weight 

limit. Try less weight.

2. Lower the lift all the way to the bottom and the red light 

should go out, resetting the protection circuit.

3. Check for dirt or other foreign materials in the lift 

mechanisms and for interference of the lifting attachment 

with other objects. If the lift is obstructed, this may activate 

the overload protection circuit. To reset the circuit, repeat 

Step 2.

The unit is very difficult to roll.

1. Check that the floor and/or caster brake(s) is/are not 

engaged.

2. Lift the lifting attachment and inspect the front casters for 

obstructions.

The unit will not charge.

1. Check to make sure the charger is fully plugged into the 

outlet and the charging port of the unit.

2. Check that the circuit breaker is not tripped.

3. Check that the battery is connected.

WARNING

Read all labels before use.

Do not exceed rated weight capacity - 150 lbs

1-800-MAGLINE (624-5463) • www.magliner.com

Platform Label

LiftPlus Labels

WARNING

!

Falling Hazard.  Do not stand on lift platform.

Do not exceed rated weight capacity - 150 lbs.

Tipping Hazard.  Keep load centered.

Содержание LiftPlus Lite

















Отзывы: