manualshive.com logo in svg

Magliner CooLift CPA48, Руководство пользователя

Поделиться
Скачать
Magliner CooLift CPA48 Скачать руководство пользователя страница 15

       1-800-MAGLINE (624-5463) 

 

 

 Page 15                                               www.magliner.com

CooLift

®

Using the AC Charging Unit

Note:

  

A completely drained battery needs 5 hours to fully charge. 

1)  Connect the AC charger plug to an AC outlet (120v domestic or 230v international
2)  Disconnect the charging unit from the charging port.

The LED will illuminate to indicate one of the following conditions:

 

Solid Yellow – Battery is charging

 

Solid Green – Battery has fully charged and is ready for use

 

Flashing Green – The output is not connected; check all connectors and fuses  

    
NOTE:  There are two operational fuses on the charging unit located at each end. A spare fuse is 
located adjacent to the main power connection.  

Note: Battery may be charged as often as desired.  Magline recommends charging at least 
once after each delivery route is complete.

Battery Meter Operating Instructions

•  Battery meter will show the charged state of the battery whenever the main power switch is 

turned ON

•  During normal operation, the charged state of the battery is indicated by the number of bars 

displayed on the meter

•  Full charge is 10 steady bars
•  A partial charge is two to nine steady bars
• 

A low battery is two alternately flashing bars

•  While the battery charger is plugged in and charging the battery, the display will repeatedly 

scroll across the bars up to the level of charge in the battery

•  Full charge is indicated by scrolling across 10 bars
•  A partially charged battery is indicated by scrolling across two to nine bars

•  When the main power switch is OFF, the battery meter will not display

Содержание CooLift CPA48





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды