background image

Temperature setting 

  Unlock the control panel by pressing the   pad for approximately 3 seconds. Once the control 

panel is unlocked an audible beep will be heard and the   indicator will go out. 

 

  Under normal conditions the temperature display indicates the current temperature of the 

corresponding zone. When adjusting the temperature, the temperature display will flash to 
indicate that the temperature is being adjusted. 

 

  The temperature in both upper zone and lower zone can be set independently by pressing  

     

 (warmer) or 

 (colder) pads that correspond to desired zone. The temperature range of 

both zones can be set between 39°F to 61°F (4° to 16°) +/- 5°F.  
 

  When the pad 

 (warmer) or 

 (colder) is pressed, the temperature displayed will increase 

or decrease in an increment of one degree.  If the pad 

 (warmer) or 

 (colder) is pressed 

and held for 2 seconds, the temperature displayed will increase or decrease in a speed of one 
degree per half second.  

 

  Once you have adjusted the upper or lower zone to the desired temperature, release the 

temperature pad. At this time the temperature displayed will flash for approximately 3 seconds 
to confirm the selected temperature. Once the display stops flashing the temperature display 
will indicate the current temperature of that zone. 

 
Note: 

The temperature display can be changed between Celsius and Fahrenheit by simultaneously 
pressing and holding both pads 

 (warmer) and 

 (colder) for the upper zone for 

approximately 3 seconds.   This unit cannot be in   (Lock) mode to perform this operation. 

 
 

Interior Light 
 

To turn on / off the interior light, press the 

 (

Light) pad.  The unit cannot be in the   (Lock) mode to 

perform this operation.  

Note: The light will turn on / off after the touch pad is released. 

 
 
 
 

AUTOMATIC DEFROST 

 

There is no need for manual defrosting of this appliance due to automatic defrosting function.   

 

The ice build-up on the inner back wall during compressor operation will be automatically 
defrosted in a compressor off cycle. 

 

When defrosting is in process, the indicators   for both zones will go off, and the circulation fans 
for both zones will run. 

 

Defrost water will drain out passing through the drain outlet in the inner back wall into a drain pan 
located above the compressor, from where it evaporates. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

                                                                                                                                              

    EN 

7

Содержание MCWC44DZ












Отзывы: