Magic Chef MCSCD3W, Руководство пользователя

Страница: 10 / 24

CARE AND MAINTENANCE
Regular inspection and maintenance will help to prevent malfunction. It is recommended to check and maintain the following items.
DOOR AND DOOR SEAL
Clean door gasket with a damp cloth regularly. Never use a steam cleaner to clean the dishwasher. We are not liable for any consequential damage if steam cleaner is used. Regularly wipe the
door and control panel with a damp cloth. Do not use sponges or materials with a rough surfaces or abrasive detergents, as these could scratch the surfaces.
FILTER ASSEMBLY
Remove any larger food particles trapped in the filters after each wash cycle by rinsing the filters under running water. Remove the coarse and fine filter from the flat filter by turning the
assembly counter-clockwise, and separate them by also turning counter-clockwise. Rinse under running water until any food particles are removed, then reassemble and let dry. There is also a
screen filter on the water fill hole under the tank lid that can be twisted counter-clockwise to remove for periodic cleaning under running water.
NOTE: The entire filter assembly should be
cleaned at least once a week.
NOTE: The entire filter assembly should be cleaned at least once.
WARNING:
Never run the dishwasher without the filters in place.
SPRAY ARM
Check if the spray arm has deposits of grease and lime scale. Lime scale, grease and dirt in the rinsing water can block the nozzles or prevent the bearing assemblies of the spray arm from
working properly. Check the outlet nozzles on the spray arm regularly. To clean, lift the spray arm upwards to detach from the dishwasher and clean it under running water. Replace in the
dishwasher after cleaning and lock the spray arm into position.
If needed, add dishwasher detergent and start the [
Heavy wash] mode in an empty chamber.
WASTE WATER PUMP
Larger food remnants which are not filtered out by the filtration system may block the waste water pump. Rinsing water will not be pumped out and result in a blockage. If this happens, turn off
the unit and disconnect the appliance from the power supply. Remove all the filters and remnants. Remove any water from inside the dishwasher and check and clean the filters.
CLEANING PRECAUTIONS
1. NEVER use chlorinated household detergents. Doing so can pose a health hazard.
2. ALWAYS unplug the appliance and let it cool down completely before cleaning.
3. Keep the body and door window clean. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the door window as they can scratch the surface, which may
result in shattering of the glass.
CAUTION:
DO NOT allow water to penetrate any gaps in the body of the unit or the steam exhaust vent when cleaning the appliance.
4. If the control panel gets wet, wipe it dry with a soft and dry cloth. DO NOT use coarse materials or abrasive cleaners to clean the control panel. When cleaning the
control panel, open the door to prevent the appliance from accidentally turning on.
5. DO NOT use poisonous or corrosive detergents to clean the appliance.
6. Dry all parts thoroughly before connecting the dishwasher to an electrical outlet.
7. Allow the appliance to cool down completely and clean it before storing. Place the unit in a box and store in a cool, dry location.
8. DO NOT wrap the power cord tightly around the appliance or put any pressure on the power cord when storage to avoid damaging the power cord.
TROUBLESHOOTING
Error Code
El
E3
E4
Cause
The door is open
Water level is too low
Water level is too high, risking
overflow
Solution
Make sure door is firmly closed
Turn the unit off and disconnect from the power
supply. Contact customer service for assistance.
Turn the unit off and disconnect from the power
supply. Contact customer service for assistance.
E7
Temperature sensor circuit is open
Turn the unit off and disconnect from the power
supply. Contact customer service for assistance.
ES
E9
Temperature sensor circuit is
shorted
Failure of water inlet pump or
problem with water intake
Turn the unit off and disconnect from the power
supply. Contact customer service for assistance.
Turn the unit off and disconnect from the power
supply. Contact customer service for assistance.
10