MAFI MT 25 Скачать руководство пользователя страница 84

Страница: 84 / 128

MAINTENANCE WORK

ELECTRICAL SYSTEM

Maintenance manual MT 25 / 30 YT

Check acid level of vehicle battery

Fig. 59: Sealing plug

Unscrew the sealing plugs of the batteries.
The acid level in the battery should lie approx. 10 mm over
the upper edge of the plate.

Refill with destilled water if necessary to adjust the acid
level.

Screw in the sealing plugs.

Check battery charge

The battery charge status of the batteries can be determined
by battery's acidity. The acid density of the battery should be
1.28 g/cm

. If the acid density is less than 1.23 g/cm

, then the

battery needs to be recharged.

Use an acid tester to determine the acid density.

Charging the battery

Fig. 60: Battery terminals

Check the battery acid level,

see “Check acid level of vehicle

battery” on page 82

Loosen the battery terminals and take them off.
Note sequence – first negative battery pole, then positive
battery pole.

Screw out the sealing plugs.

Connect the charger.
Note sequence – first connect the positive battery poles,
then negative battery poles of battery and charger.

Switch on the charger.

Once the battery is charged, disconnect the charging
device.
Note sequence – first disconnect the negative battery poles,
then positive battery poles of battery and charger.

Check the battery acid level once more.
A lowered acid level can indicate a defective cell.

Screw in the sealing plugs.

Connect the battery terminals.
Note sequence – first positive battery pole, then negative
battery pole.

Check battery poles and connections

Connect the battery terminals for corrosion.

Check the terminals for proper tightness.

Check whether the terminals have been greased sufficiently
(special grease).

Содержание MT 25

































































































































Результаты поиска

Содержание MT 25

Отзывы:

Похожие инструкции для MT 25

Бренды по названию

Популярные бренды

MAFI MT 25, Руководство по обслуживанию

Результаты поиска

Содержание MT 25

Отзывы:

Похожие инструкции для MT 25

Бренды по названию

Популярные бренды