Maestro MR928, Руководство пользователя

Страница: 4 / 15

6 7
Purchase industrial devices for commercial use.
Actions in extreme situations
- If a device tumbled into water, immediately, unplug the device, not touching to
the device or water.
- In case of appearance from appliance of smoke, sparkling, strong smell of a
burn isolation, immediately stop use the device, unplug the device, appeal to the
nearest service center.
Operation
Before the first use
Before you use it for the first time, remove the packing materials, unwind the
power cord completely. Make sure that all parts of the device are not damaged.
Ensure that the heater is not positioned close to curtains or furniture as this could
create a fire hazard. Strictly observe the distances to the surrounding objects
mentioned below.
Assembly for floor standing use
-Before using the heater, the feet (supplied separately in the carton), must be
fitted to the unit. These are to be attached to the base of the heater using the 4
self-tapping screws provided, taking care to ensure that they are located correctly
in the bottom ends of the heater side moldings. See Picture 2.
-Put the heater vertically on a firm dry horizontal surface. Always use the heater
in an upright position. Provide adequate air space above and on all sides for air
circulation. To ensure normal air circulation the heater shall be installed in place
where a clean space is at least 50 cm meter above outlet grid, and 50 cm for
front, side and back parts in all directions from walls, furniture and similar objects.
Wall – hanging use
ATTENTION! The wall and coating materials must be non-flammable. They
must be resistant to the surface temperature of the convector.
The heater should be installed in place on the wall where a clean space is at least
50cm meter above outlet grid to ceiling, 50 cm from front, 20cm side parts, and 20
cm above the floor.
Installation (Picture 3)
1.Measure the distance between the two slots situated at the back of the
appliance
2.Drill two holes at the same distance in the wall and insert a plug in each hole
you just drilled. Place the brackets facing the holes as indicated on picture B and
attach them in this position with the screws supplied.
3.Before attaching the appliance on the brackets, attach the two other brackets
underneath the appliance as indicated.
4.Attach the appliance on the wall. To do so, hold it in such way that the
slots are facing the brackets; insert the appliance halfway onto the brackets until
the appliance can go down into the grooves of the brackets.
5.As soon as the appliance is positioned correctly, take a pencil and mark a dot in
the hole of each bracket situated underneath the appliance.
6.Then take off the appliance by proceeding the other way around compared to
point 4 above.
7.Drill a hole in the wall on each dot you just marked and insert a plug in each
hole.
8.Attach the appliance back on the wall as indicated in point 4, insert screws
through the brackets underneath the appliance and tighten without forcing.
Operation Switch
Switch positions (2/Picture1):
“O” - heating OFF
“I” - Low heat output, low power
“II” - High heat output, full power.
Thermostat (3/Picture1):
“min”(thin end of mark) the minimum room air temperature
“max” (thick end of mark) the maximum room air temperature
How to use
- Before connection the plug to the mains make sure that the device switch is set
into «O»- «OFF» position.
- Plug the heater into a suitable power outlet (observing all the instruction
regarding positioning).
Attention! When switched on for the first time a slight odor might be emitted for
a few minutes. This is harmless and occurs with most heaters when any slight
traces of dust or lubricants that may have collected in the factory are heated
away.
- Turn the control knob (2/Picture1) to “I” for low heat and “II” for full heat. The
indicator will light signaling that the device has turned on. For maximum heat
output use “II” with the thermostat (3/ Picture1) turned fully clockwise.
- Set the level of heat by turning the thermostat dial gradually clockwise for the
lowest heat and fully clockwise for maximum.
- The thermostat will turn the machine off when the selected room heating is
achieved, and when the temperature drops it will turn on again automatically.
EN