Maestro 42.598.13, Оригинальная инструкция по эксплуатации

Страница: 7 / 36

Additional information for electric power tools Ÿ
The supplied additional handle (8) must first be
m Warning!
fitted. To do this, the clamp must be opened by
The specified vibration value was established in turning the handle until it is wide enough for the
accordance with a standardized testing method. It additional handle to be slid over the chuck (1) and
may change according to how the electric equipment on to the hammer drill.
is used and may exceed the specified value in Ÿ
After you have positioned the additional handle (8),
exceptional circumstances.
turn it to the most comfortable working position for
you.
The specified vibration value can be used to compare
Ÿ
Now turn the handle in the opposite direction again
the equipment with other electric power tools.
until the additional handle is secure.
Ÿ
The additional handle (8) is suitable for both
The specified vibration value can be used for initial
lefthanded and right-handed users.
assessment of a harmful effect.
5.2 Fitting and adjusting the depth stop
Keep the noise emissions and vibrations to a
(Fig. 4/Item 2)
minimum.
The depth stop (2) is held in place by the additional
handle (8) by clamping. The clamp can be released
Ÿ
Only use appliances which are in perfect working
and tightened by turning the handle.
order.
Ÿ
Release the clamp and fit the depth stop (2) in the
Ÿ
Service and clean the appliance regularly.
recess provided for it in the additional handle.
Ÿ
Adapt your working style to suit the appliance.
Ÿ
Set the depth stop (2) to the same level as the drill
Ÿ
Do not overload the appliance.
bit.
Ÿ
Have the appliance serviced whenever necessary. Ÿ
Pull the depth stop back by the required drilling
Ÿ
Switch the appliance off when it is not in use. depth.
Ÿ
Wear protective gloves.
Ÿ
Turn the handle on the additional handle (8) until it
is secure.
Residual risks Ÿ
Now drill the hole until the depth stop (2) touches
the workpiece.
Even if you use this electric power tool in
accordance with instructions, certain residual
5.3 Fitting the drill bit (Fig. 5)
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
Ÿ
Always pull the power plug before making
construction and layout:
adjustments to the equipment.
Ÿ
Release the depth stop (2) as described in 5.2 and
1. Lung damage if no suitable protective dust
push it towards the drill handle. This provides free
is used.
access to the chuck (1).
2. Damage to hearing if no suitable ear protection
Ÿ
Undo the chuck by turning it anti-clockwise with the
used.
supplied chuck key (9).
3. Health damage caused by hand-arm vibrations
Ÿ
To ensure that it is perfectly positioned the drill bit
the equipment is used over a prolonged period
or tool should be inserted as far as possible into the
is not properly guided and maintained.
chuck. After inserting the drill bit or tool, tighten the
chuck (1) by turning the chuck key (9) clockwise
5. Before starting the equipment
until the drill bit or tool is secure. Check that the drill
bit is secure in the chuck (1).
Before you connect the equipment to the mains Ÿ
Check at regular intervals that the drill bit or tool is
supply make sure that the data on the rating plate
secure (pull the mains plug).
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
6. Operation
5.1. Fitting the additional handle (Fig. 2-3/Item 8)
6.1 ON/OFF switch (Fig. 6/Item 5)
Ÿ
First fit a suitable drill bit into the tool (see 5.3).
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
Ÿ
Connect the mains plug to a suitable socket.
use the tool without the additional handle.
Ÿ
Position the drill in the position you wish to drill.
The additional handle (8) is secured to the hammer
drill by a clamp. During the handle clockwise tightens
To switch on:
this clamp. Turning it anti-clockwise will release the
Press the ON/OFF switch (5)
clamp.
7
GB