Maddox MF15-1 Скачать руководство пользователя страница 4

Page 4

For technical questions, please call 1-888-866-5797.

Item 56803

Setup Instructions

1.  Open the Cup (3).

2.  Seat the O-ring (11) completely into 

the groove in the top of the Cup.

3.  Remove the shipping spacer that 

prevents the Vacuum Pump (1) handle 
from moving through its full range. 

4.  Cover the inlet of the Vacuum Pump 

with something such as a plastic bag.   

To prevent injury, DO NOT USE 
YOUR SKIN TO PLUG THE INLET.

  

Operate the pump several times to 
create the vacuum.  The vacuum 
should not decrease quickly.  If air 
is entering through the vacuum 
release valve, tighten it.  After the 
pump properly holds a vacuum, 
press in the Pump’s vacuum release 
valve to release the vacuum.  
Set the plastic bag aside.

5.  The vacuum pump should 

now be ready for use.

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the 
beginning of this document including all text under subheadings therein 
before set up or use of this product.

Note:

  For additional information regarding the parts listed in the following pages,  

refer to 

Parts List and Diagram

 on page 7.

Vacuum System Testing

WARNING! Avoid carbon monoxide 
poisoning!  Never run a gasoline 
engine in an enclosed garage 
or other contained area.

1.  Position the vehicle in a flat, level 

outdoor area.  Set the parking 
brake and chock the tires.

2.  Attach a 23" Hose (4) to 

the Vacuum Pump (1).

3.  Attach the other end of the Hose to 

the vacuum system.  Keep clear of 
parts that will move or get hot while 
an assistant starts the engine.  
Wait until the vacuum reading 
stabilizes and compare it to the 
manufacturer’s specification.

4.  After obtaining a measurement, 

shut off the engine.

5.  A low or unstable vacuum reading 

may mean a vacuum leak, 
vacuum line blockage, cylinder 
sealing problems, incorrect valve/
ignition timing, or other issues.

Note:  

Vehicle vacuum systems will 

differ.  Consult the vehicle’s service 
manual for proper testing procedures.

6.  After testing is complete, disconnect 

the Vacuum Pump and Hose, 
remove any plugs or clamps 
and secure all vacuum lines.

Содержание MF15-1









Отзывы: