background image

9

Bottom right woofer replacement:

  22

 

Eight screws need to be removed 

from the woofer using the phillips head 

screwdriver. Once the screws are 

removed, the woofer may be loosened 

by prying a fl at head screwdriver in 

between the cabinet and the woofer; 

a good place to start is in the notches 

located just below the horn assembly 

and above the woofer (as pointed out 

by the arrows in the picture above). 

Also note the “tinsel dressing teardrops” 

(circled above) which are facing 

upwards. The woofer should be placed 

back the same way. It is for visual 

consistency. More importantly, the 

cables from the printed circuit board to 

the woofer terminals are quite short; it 

probably would not work otherwise. The 

eight screws should be kept in a safe 

place.  

8

8

11

22

33

44

55

66

77

99

10

10

11

11

12

12

11

22

33

44

55

66

77

88

  11

 

Six screws need to be removed from 

each side of the front of the grill (twelve 

screws total) using the phillips head 

screwdriver. This grill has a tendency to 

want to “pop” off, so please be sure to 

hold it in place with one hand or arm 

while removing the screws with your 

free hand. In addition to the grill, the 

screws also hold the decorative trim. The 

trim should be removed, too. Keep the 

twelve screws in a safe place.

Содержание S408




















Отзывы: