background image

7

Owner’s Manual

Owner’

s Manual

DS3232 Features

Front Panel

All the connection points (other than the power cord) 

are located on the front panel for easy accessibility when 
rack mounted.

1. Network Connection 

This RJ45 connector transfers the digital audio and 

control data between the DS3232 and the mixing con-
sole. Use a standard Cat5e Ethernet cable to make this 
connection.

This is a Neutrik® EtherCon® connector that 

features a secure latching system when used with the 
Neutrik male cable carrier for preassembled RJ45 plugs.

2. POWER Indicator 

This green LED lights up when the POWER switch is 

turned on and the linecord is attached and plugged into 
an AC power source. 

3. COMM   Indicator 

This LED lights up to indicate that communication is 

established between the DS3232 and the mixing console 
via the U100 Network card.

4. INPUTS 1-32

These are female XLR connectors, which accept a 

balanced microphone input from almost any type of 
microphone. The microphone preamps feature our latest 
remote-controlled design, with higher fidelity and headroom 
rivaling most standalone mic preamps on the market today.

The XLR inputs are wired as follows: 

 

Pin 1 = Shield or ground 

 

Pin 2 = Positive (+ or hot) 

 

Pin 3 = Negative (– or cold)

These XLR connectors are also equipped with 48V 

phantom power, which can be turned on and off from 
the mixing console.

The routing of the 32 inputs on the DS3232 is config-

ured by the mixing console. Generally, this will be done 
in the Setup window for the expansion cards where the 
U100 Network card is installed.

If you are connecting a line-level signal to one of the 

inputs, engage the PAD for that input. This reduces the 
input sensitivity of the mic preamp so it can accept a 
line-level signal. Also, make sure that phantom power 
isn’t turned on for that channel. It could damage the 
output stage of the line-level device you have connected 
to the XLR balanced input.

Note:

 Phantom power should only be 

used with microphones designed to 
accept it.

RETURNS

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

25

26

27

28

29

30

31

32

17

18

19

20

21

22

23

24

U-NET

DS3232

24-BIT / 96kHz DIGITAL SNAKE

INPUTS

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

25

26

27

28

29

30

31

32

17

18

19

20

21

22

23

24

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

PUSH

POWER

Содержание DS3232 Digital Snake

















Отзывы: