![background image](http://html1.mh-extra.com/html/mack/granite-gu-series/granite-gu-series_operators-handbook-manual_686197077.webp)
66 INSTRUMENTS AND CONTROLS
4. Exhaust Pyrometer (If Equipped)
– Indicates the temperature of
exhaust gases (about 12 to 16 inches from the diesel particulate filter inlet
connections). This helps the operator select the proper gear for load and
grade conditions, thereby avoiding excessive exhaust temperatures.
CAUTION
Do NOT exceed the maximum exhaust temperature indicated by the red line on
the gauge. To reduce exhaust temperature, downshift or reduce engine power. If
operating in cold climates with a winterfront, open the winterfront.
5. Transmission Oil Temperature Gauge (If Equipped)
– Indicates
transmission oil temperature.
CAUTION
The maximum safe oil temperature for MACK transmissions is 121°C (250°F) for
mineral-based oil, or 148°C (300°F) for synthetic oil. Continued with oil above
this temperature will cause rapid deterioration of the oil’s lubricating properties
and is NOT recommended. Consult the vendor manual for non-MACK components.
6. Aftertreament DEF Tank Level gauge
7. Integrated Temp-A-Start (Amber) (If Equipped)
– "Integrated
Temp-A-Start" saves fuel by reducing the amount of time spent idling to keep
the vehicle’s batteries charged, the engine warm, or the cab and sleeper
comfortable. Once the optional ’Integrated Temp-A-Start’ feature is activated
via a dash switch, the system will automatically start and stop the truck engine.
Safety overrides prevent the system from activation if the transmission is in
gear, the hood is up, or the parking brake is released. Integrated Temp-A-Start
voltage and temperature target settings are fully programmable through either
VCADS service support software, or, if enabled via the Co-Pilot instrument
cluster display
8. Wait to Start (Amber) (If Equipped)
– Indicates that the intake pre-heat is
enabled. Wait to start engine until light goes out.
9. Transmission Oil Temperature Indicator (Red)
– A red tell-tale light that
illuminates when transmission oil temperature reaches a pre-determined level
(depending on transmission make and model) indicating an overheat condition.
10. Electronic Malfunction Indicator (Amber)
– Illuminates when V-MAC®
detects an electronic malfunction. Refer to the
V-MAC® IV Operator’s Guide
.
The electronic malfunction lamp may turn on when operating the vehicle in
a bob-tail mode with the engine brake turned on and cruise control active.
Содержание Granite GU Series
