background image

Notes:

1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons.

2.The UV-protected side of the sheet is covered with opal white film and

must face towards the sun.

3.Remove approximately 2 inches of film from all sheet edges before

installing.Removing all film immediately after the construction is

completed

4.Make sure the greenhouse is located on a flat, level surface.

TO PREVENT INJURY, READ AND UNDERSTAND THE

GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE.

GENERAL SAFETY, WARNINGS AND PRECAUTIONS

KEEP WORK AREA CLEAN AND DRY

.

Cluttered, damp or wet work areas invite injuries.

STAY ALERT. Watch what you are doing at all times. Use common

sense. Do not use the greenhouse when you are tired or distracted from

the job at hand. It is recommended to use gloves for assembling the

greenhouse.

MAINTAIN THIS PRODUCT WITH CARE

.

Keep the greenhouse clean and dry for better performance:

maintenance should be performed regularly.

USE THE RIGHT PRODUCT FOR THE JOB

.

Do not attempt to force a small product to do the work of a larger

industrial product. There are certain applications for which the

greenhouse was designed. It will do the job better and more safely in the

manner for which it was intended. Do not modify the greenhouse and do

not use the greenhouse for a purpose for which it was not intended.

MAINTAIN A SAFE WORKING ENVIRONMENT

.

Keep the work area tidy. Make sure there is adequate surrounding

workspace. Avoid high traffic areas. Always keep the work area free of

obstructions, grease, oil, trash and other debris.

PROPER GREENHOUSE LOCATION.

Make sure the greenhouse is located on a flat, level surface.

TO PREVENT INJURY, PLEASE READ AND UNDERSTAND THE 

GREENHOUSE ASSEMBLY INSTRUCTIONS MANUAL BEFORE 

USE.

Notes:

1. Around 2-3 hours is needed to assemble the greenhouse by 2-3 

individuals.

2. The UV-protected side of the panel sheets is covered with opal 

white film and must be placed facing the sun.

3. Before installing the sheets, remove around 2 inches of film from all 

the edges. Once the construction is completed, remove the the entire 

film immediately.

4. Ensure that the greenhouse is located on a flat and level surface.

GENERAL SAFETY, WARNINGS AND PRECAUTIONS

KEEP WORKING AREA CLEAN AND DRY.

Cluttered, damp or wet working areas invite injuries.

BE ALERT. Always be cautious of your actions. Use your common 

sense. Do not assemble the structure if you are tired or distracted. 

Use gloves when assembling the greenhouse.

HANDLE THIS PRODUCT WITH CARE

Keep the greenhouse clean and dry to maintain better performance. 

Also, regular maintenance must be done.

USE THE SUITABLE TOOLS FOR THE JOB

Do not use small tools in lieu of larger ones. Tools are not suitable for 

every type of work. The greenhouse is designed in order to provide 

better condition and safety. So, do not perform any modification on 

the greenhouse. Do not use it aside from its intended purpose.

MAINTAIN A SAFE WORKING ENVIRONMENT

Keep your working area clean and organized. Make sure that there is 

enough space for you to work on. Avoid crowded areas. Also, keep 

source of obstruction, grease, oil or trash far from your working zone.

PROPER GREENHOUSE LOCATION

Place the greenhouse on a flat and level surface.

Notes:

1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons.

2.The UV-protected side of the sheet is covered with opal white film and

must face towards the sun.

3.Remove approximately 2 inches of film from all sheet edges before

installing.Removing all film immediately after the construction is

completed

4.Make sure the greenhouse is located on a flat, level surface.

TO PREVENT INJURY, READ AND UNDERSTAND THE

GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE.

GENERAL SAFETY, WARNINGS AND PRECAUTIONS

KEEP WORK AREA CLEAN AND DRY

.

Cluttered, damp or wet work areas invite injuries.

STAY ALERT. Watch what you are doing at all times. Use common

sense. Do not use the greenhouse when you are tired or distracted from

the job at hand. It is recommended to use gloves for assembling the

greenhouse.

MAINTAIN THIS PRODUCT WITH CARE

.

Keep the greenhouse clean and dry for better performance:

maintenance should be performed regularly.

USE THE RIGHT PRODUCT FOR THE JOB

.

Do not attempt to force a small product to do the work of a larger

industrial product. There are certain applications for which the

greenhouse was designed. It will do the job better and more safely in the

manner for which it was intended. Do not modify the greenhouse and do

not use the greenhouse for a purpose for which it was not intended.

MAINTAIN A SAFE WORKING ENVIRONMENT

.

Keep the work area tidy. Make sure there is adequate surrounding

workspace. Avoid high traffic areas. Always keep the work area free of

obstructions, grease, oil, trash and other debris.

PROPER GREENHOUSE LOCATION.

Make sure the greenhouse is located on a flat, level surface.

TO PREVENT INJURY, PLEASE READ AND UNDERSTAND THE 

GREENHOUSE ASSEMBLY INSTRUCTIONS MANUAL BEFORE 

USE.

Notes:

1. Around 2-3 hours is needed to assemble the greenhouse by 2-3 

individuals.

2. The UV-protected side of the panel sheets is covered with opal 

white film and must be placed facing the sun.

3. Before installing the sheets, remove around 2 inches of film from all 

the edges. Once the construction is completed, remove the the entire 

film immediately.

4. Ensure that the greenhouse is located on a flat and level surface.

GENERAL SAFETY, WARNINGS AND PRECAUTIONS

KEEP WORKING AREA CLEAN AND DRY.

Cluttered, damp or wet working areas invite injuries.

BE ALERT. Always be cautious of your actions. Use your common 

sense. Do not assemble the structure if you are tired or distracted. 

Use gloves when assembling the greenhouse.

HANDLE THIS PRODUCT WITH CARE

Keep the greenhouse clean and dry to maintain better performance. 

Also, regular maintenance must be done.

USE THE SUITABLE TOOLS FOR THE JOB

Do not use small tools in lieu of larger ones. Tools are not suitable for 

every type of work. The greenhouse is designed in order to provide 

better condition and safety. So, do not perform any modification on 

the greenhouse. Do not use it aside from its intended purpose.

MAINTAIN A SAFE WORKING ENVIRONMENT

Keep your working area clean and organized. Make sure that there is 

enough space for you to work on. Avoid crowded areas. Also, keep 

source of obstruction, grease, oil or trash far from your working zone.

PROPER GREENHOUSE LOCATION

Place the greenhouse on a flat and level surface.

www.machrus.com

Содержание OGAL-666A






























Отзывы: