MacDon R116 Скачать руководство пользователя страница 165 | Manualshive

Страница: 165 / 234

background image

214713

157

Revision A

8.3

Transport Lighting

8.3.1

Lighting (With Road Friendly Transport

™

™

Option)

1015026

A

B

Figure 8.7: Lighting Locations (with Road
Friendly Transport

™

™

)

The disc mower is equipped with two bidirectional amber
lights (A) located on the outboard edges of the carrier frame
that function as flashing hazard lights and turn signals.

The red lights (B) located on the inboard side of the amber
lights function as both tail and brake lights. Refer to the disc
mower operator

’

s manual for information about connecting

the electrical harness to the tractor.

Amber reflective tape is applied to various locations on the
front and sides of the disc mower, hitch, and carrier frame.
Red reflective tape is applied to the rear of the disc mower.

8.3.2

Lighting (Without Road Friendly Transport

™

™

Option)

1015020

B

A

Figure 8.8: Lighting Locations

The disc mower is equipped with two bidirectional amber
lights (A) located on the outboard edges of the carrier frame
that function as flashing hazard lights and turn signals.

The red lights (B) located on the inboard side of the amber
lights function as both tail and brake lights. Refer to the disc
mower operator

’

s manual for information about connecting

the electrical harness to the tractor.

Amber reflective tape is applied to various locations on the
front and sides of the disc mower, hitch, and carrier frame.
Red reflective tape is applied to various locations on the
disc mower.

TRANSPORTING THE DISC MOWER

«
...
163
164
165
166
167
...
»

Содержание R116











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R116

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: XAG Страницы: 24

Бренд: AAON Страницы: 36

Бренд: Danelec Страницы: 67

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Бренд: Yuwell Страницы: 2

Бренд: Park House Healthcare Страницы: 32

Бренд: Teac Страницы: 2

Бренд: Cuisinart Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды