MAC TOOLS AW3800 Ultra Duty Скачать руководство пользователя | Manualshive

Страница: 38 / 69

background image

38

MAINTENANCE SECTION

TROUBLESHOOTING GUIDE

Trouble

Probable Cause

Solution

Low power

Dry Motor

Daily, inject 3 cc of Mac Tool Pneumatic Oil into
the inlet and run the tool to lubricate the motor.

Inadequate air supply

Install proper air supply and connection. Refer to
Dwg. TPD905–1 and Dwg. TPD2034 on Page 3.

Dirty Inlet bushing Screen

Using a clean, suitable, cleaning solution in a well
ventilated area, clean the Inlet Bushing Screen.

Worn or broken Vanes

Replace a complete set of Vanes

Worn or broken Cylinder and/or
scored End Plates

Examine Cylinder. Check outside and ends for
wear or damage and inside for scored or wavy
bore.
Replace Cylinder if any of these conditions exist.
Replace End Plates if they are scored.

Dirty motor parts.

Disassemble the Tool and clean in a clean, suit-
able, cleaning solution in a well ventilated area.
Assemble the Tool and inject 3 cc of the
recommended oil into Inlet and run Tool to
lubricate internal parts.

Damaged Reverse Valve

Replace Reverse Valve. Refer to Installation of
Reverse Valve.

Motor will not run

Incorrect assembly of motor

Disassemble motor and replace worn or broken
parts and reassemble. Refer to Assembly of the
Motor.

Insufficient lubricant in impact
mechanism.

Lubricate impact mechanism through Hammer
Case Grease Fitting using the recommended
grease.

Tool will not impact

Broken or worn impact mecha-
nism parts

Remove Hammer Case Assembly and examine
impact mechanism parts. Replace any worn or
broken parts.

Impact mechanism not
assembled correctly.

Refer to Assembly of Impact Mechanism.

SAVE THESE INSTRUCTIONS. DO NOT DESTROY.

«
...
36
37
38
39
40
...
»

Содержание AW3800 Ultra Duty






































































Отзывы:

Нет отзывов

Похожие инструкции для AW3800 Ultra Duty

Бренд: Hilti Страницы: 240

Бренд: Kobalt Страницы: 95

CID 12V/80 PLUS

Бренд: F.F. Group Страницы: 72

Бренд: RAD Torque Systems Страницы: 10

Бренд: Metabo Страницы: 30

PowerMaxx SSD 12

Бренд: Metabo Страницы: 68

EYFLA3J - DRILL - MULTI LANGUAGE

Бренд: Panasonic Страницы: 168

Бренд: Panasonic Страницы: 152

Бренд: Makita Страницы: 12

Бренд: Makita Страницы: 92

Бренд: Draper Страницы: 24

Бренд: Facom Страницы: 48

Бренд: Universal Tool Страницы: 8

Бренд: Universal Tool Страницы: 8

Бренд: Universal Tool Страницы: 8

Бренд: Universal Tool Страницы: 7

Бренд: Narex Страницы: 40

1/2 inch Air Impact Wrench

Бренд: Ozito Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды