background image

MOOD LIGHTS

Essence - O     Designer - O     Classic - O

ALL SYSTEMS EXCEPT THOSE UTILIZING SMART-TOUCH CONTROL

One light - 5 different colored lenses.
Two lights -10 colored lenses (2 of each color).
Mood lights are controlled by a remote wall switch.

CHANGING LENS OR BULB:

Danger of electrical shock: Before changing a lens or bulb,
drain tub and disconnect power.

1) Remove lens with special tool furnished.  
2)  Pull bulb straight out.  
3)  Gently push in new bulb.  
4)  Make certain that the "O" ring is in place.  
5)  Replace lens with tool. 
6)  Tighten with tool to align with notch. 

These miniature light bulbs are available at lighting and hardware stores.
(12 Volt- 10 Watt)

SMART-TOUCH CONTROL SYSTEMS

One light or two lights - LED bulbs (not serviceable by the homeowner).
Mood lights are controlled by the Smart-Touch control. See page 7, 

Turning the

Bath Lighting On and Setting the Lighting Options, 

for information on how to

operates these lights.

BATH WASTE

Essence - S 

Designer - S 

Classic - O

The high quality bath waste that is included with your Pearl is cable operated, not
the common linkage type found in most tubs which are subject to clogging prob-
lems.  The drain plug has an adjustable screw and locking nut to vary the overall
length of the plug.  If the bath waste drain does not seal, turn in the screw and
retighten the locking nut (fig. 7).

VALVES & HAND HELD SPRAY

Essence - S* 

Designer - NA

Classic - NA

(* Except the Wisteria)

All Pearl Essence Series units, except the Wisteria, have these features.  Designed
for convenience and function, yet sculpted into their own special place.  The
spray is adjustable on the spray head itself, from full spray to stream.  Push the
diverter down to change from tub fill to hand held spray.  The valves are ceram-
ic requiring only a 

1

4

turn for on/off operation (fig. 8).

IMPORTANT
Proper installation of the connecting lines from the valves to the fill spout and
hand held spray, in compliance with local codes is the responsibility of the
installer. A vacuum breaker and/or temperature balanced valve may be
required.  Pearl Baths, Inc. does not warrant connections of water supply fit-
tings and piping, fill systems or drain/overflow systems. Nor is it responsible
for damage to the bath or home which occurs during any installation proce-
dure.

fig. 8

fig. 7

5

Содержание Maax Pearl Hot Tub

















Отзывы: