MA lighting MA onPC, Руководство пользователя

Страница: 34 / 41

MA onPC
command wing
Data
Transport
Safety
instructions
Safety and
environmet
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
32
On / Off Switching
Connect / Installation
Download grandMA2 onPC -software from MA – Homepage.
MA onPC command wing needs software grandMA2 onPC V 2.5.5.0 and higher ( grandMA1 onPC is
not applicable).
Install the software „grandMA2 onPC“ on your Windows – PC or notebook. Minimum requirements
you will find at: www.malighting.com .
switch on your PC or notebook and start MA onPC.
Connect the command wing direct to your PC or notebook via a USB cable (use no hub or switch!).
Connect your PC or notebook with the other hardware. Such as shown on previous page.
Connect the power supply. The command wing is equipped with a PSU (90 -240V // 50 – 60Hz).
PAY ATTENTION TO DETAILS ON PAGE 23
ON
Set the mains switch on the rear side of the command wing to „I“.
Note: Flashing executor buttons indicates, that the position of this fader does not correspond with the
position of the virtual fader (internally stored fader position) of the onPC. Position of the virtual fader is
relevant for value output. After first movement of the command wing –fader (the “real” fader), this
position is relevant for value output.
OFF
Set the mains switch on the rear side of the command wing to „O“.
Note:
Disconnecting the MA onPC command wing from your PC or notebook is always possible – however
DMX –output is interrupted immediately.
Show is always stored on yourPC or notebook, not on your onPC command wing.
Update only possible with a PC or notebook and grandMA2 onPC.
For longer non use disconnect all cables.
MA onPC
command wing
Data
Transport
Safety
instructions
Safety and
environmet
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
32
On / Off Switching
Connect / Installation
Download grandMA2 onPC -software from MA – Homepage.
MA onPC command wing needs software grandMA2 onPC V 2.5.5.0 and higher ( grandMA1 onPC is
not applicable).
Install the software „grandMA2 onPC“ on your Windows – PC or notebook. Minimum requirements
you will find at: www.malighting.com .
switch on your PC or notebook and start MA onPC.
Connect the command wing direct to your PC or notebook via a USB cable (use no hub or switch!).
Connect your PC or notebook with the other hardware. Such as shown on previous page.
Connect the power supply. The command wing is equipped with a PSU (90 -240V // 50 – 60Hz).
PAY ATTENTION TO DETAILS ON PAGE 23
ON
Set the mains switch on the rear side of the command wing to „I“.
Note: Flashing executor buttons indicates, that the position of this fader does not correspond with the
position of the virtual fader (internally stored fader position) of the onPC. Position of the virtual fader is
relevant for value output. After first movement of the command wing –fader (the “real” fader), this
position is relevant for value output.
OFF
Set the mains switch on the rear side of the command wing to „O“.
Note:
Disconnecting the MA onPC command wing from your PC or notebook is always possible – however
DMX –output is interrupted immediately.
Show is always stored on yourPC or notebook, not on your onPC command wing.
Update only possible with a PC or notebook and grandMA2 onPC.
For longer non use disconnect all cables.
MA onPC
command wing
Data
Transport
Safety
instructions
Safety and
environmet
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
32
On / Off Switching
Connect / Installation
Download grandMA2 onPC -software from MA – Homepage.
MA onPC command wing needs software grandMA2 onPC V 2.5.5.0 and higher ( grandMA1 onPC is
not applicable).
Install the software „grandMA2 onPC“ on your Windows – PC or notebook. Minimum requirements
you will find at: www.malighting.com .
switch on your PC or notebook and start MA onPC.
Connect the command wing direct to your PC or notebook via a USB cable (use no hub or switch!).
Connect your PC or notebook with the other hardware. Such as shown on previous page.
Connect the power supply. The command wing is equipped with a PSU (120 -230V // 50 – 60Hz).
PAY ATTENTION TO DETAILS ON PAGE 23
ON
Set the mains switch on the rear side of the command wing to „I“.
Note: Flashing executor buttons indicates, that the position of this fader does not correspond with the
position of the virtual fader (internally stored fader position) of the onPC. Position of the virtual fader is
relevant for value output. After first movement of the command wing –fader (the “real” fader), this
position is relevant for value output.
OFF
Set the mains switch on the rear side of the command wing to „O“.
Note:
Disconnecting the MA onPC command wing from your PC or notebook is always possible – however
DMX –output is interrupted immediately.
Show is always stored on yourPC or notebook, not on your onPC command wing.
Update only possible with a PC or notebook and grandMA2 onPC.
For longer non use disconnect all cables.