MA lighting grandMA2 Series, Быстрое руководство

Страница: 30 / 36

NPU / RPU
Data
Transport
Important Safety
Instructions
Safety and
Environment
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
Switching the unit On/Off
Caution: Do not power down during booting. Such a switch-off may lead to corruption of the solid state disk files.
Power connector AC power switch on the back panel NPU and RPU
Position I = ON
In the I position, the instrument is in standby mode or in
operation, depending on the position of the ON/STANDBY key at
the front panel.
Note: The AC power switch may remain ON continuously.
Switching to OFF is only required when the instrument
must be completely removed from the AC power source.
Position O = OFF
The 0 position implies an all-pole disconnection of the unit from
the AC power source.
Standby switch ON/STANDBY switch on the front panel (NPU and RPU)
The ON/STANDBY switch activates two different operating Modes:
Operation ON – First push on ON/STANDBY - switch
The unit starts booting. All modules within the instrument are
supplied with power.
Note : After a current interruption the unit
automatically returns to the status before
the failure – if the switch stays in this
mode.
STANDBY – Second push on ON/STANDBY – switch
Caution: In standby mode, the AC power voltage is present within the unit
Switching On the unit
In order to switch on the unit, set the power switch on the rear panel to position I.
Set the unit to operating mode by pressing the ON/STANDBY switch on the front panel.
Switching Off the unit
In order to switch off the unit, push the ON / STANDBY switch on the front panel and confirm with the softbutton
“YES”. In this standby mode, the AC power voltage is present within the unit. For longer non use switch the power
switch to “
0 ”.
NPU / RPU
Data
Transport
Important Safety
Instructions
Safety and
Environment
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
Switching the unit On/Off
Caution: Do not power down during booting. Such a switch-off may lead to corruption of the solid state disk files.
Power connector AC power switch on the back panel NPU and RPU
Position I = ON
In the I position, the instrument is in standby mode or in
operation, depending on the position of the ON/STANDBY key at
the front panel.
Note: The AC power switch may remain ON continuously.
Switching to OFF is only required when the instrument
must be completely removed from the AC power source.
Position O = OFF
The 0 position implies an all-pole disconnection of the unit from
the AC power source.
Standby switch ON/STANDBY switch on the front panel (NPU and RPU)
The ON/STANDBY switch activates two different operating Modes:
Operation ON – First push on ON/STANDBY - switch
The unit starts booting. All modules within the instrument are
supplied with power.
Note : After a current interruption the unit
automatically returns to the status before
the failure – if the switch stays in this
mode.
STANDBY – Second push on ON/STANDBY – switch
Caution: In standby mode, the AC power voltage is present within the unit
Switching On the unit
In order to switch on the unit, set the power switch on the rear panel to position I.
Set the unit to operating mode by pressing the ON/STANDBY switch on the front panel.
Switching Off the unit
In order to switch off the unit, push the ON / STANDBY switch on the front panel and confirm with the softbutton
“YES”. In this standby mode, the AC power voltage is present within the unit. For longer non use switch the power
switch to “
0 ”.
NPU / RPU
Data
Transport
Important Safety
Instructions
Safety and
Environment
Quickstart
Connect
Quickstart
ON / OFF
Maintenance
Conformity
Switching the unit On/Off
Caution: Do not power down during booting. Such a switch-off may lead to corruption of the solid
state disk files.
Power connector AC power switch on the back panel NPU and RPU
Position I = ON
In the I position, the instrument is in standby mode or in
operation, depending on the position of the
ON/STANDBY key at the front panel.
Note: The AC power switch may remain ON
continuously.
Switching to OFF is only required when the instrument
must be completely removed from the AC power source.
Position O = OFF
The 0 position implies an all-pole disconnection of the unit from
the AC power source.
Standby switch ON/STANDBY switch on the front panel
(NPU and RPU)
The ON/STANDBY switch activates two different Modes:
Operation ON – First push on ON/STANDBY - switch
The unit starts booting. All modules within the instrument
are supplied with power.
Note : After a current interruption the unit
automatically returns to the status before the
failure – if the switch stays in this mode.
STANDBY – Second push on ON/STANDBY – switch
Caution: In standby mode, the AC power voltage is present within the unit
Switching On the unit
In order to switch on the unit, set the power switch on the rear panel to position I.
Set the unit to operating mode by pressing the ON/STANDBY switch on the front panel.
Switching Off the unit
In order to switch off the unit, push the ON / STANDBY switch on the front panel and confirm with the
softbutton “YES”. In this standby mode, the AC power voltage is present within the unit. For longer non
use switch the power switch to “
0 ”.