M2M MCF-LW12TERPM Скачать руководство пользователя страница 2

 

m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860 

 
 

Disposal information for users

 

Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of the European 
Parliament on waste electrical and electronic equipment (WEEE), and pursuant to and in

  

accordance with Article 20 of the Directive 2013/56/EU of the European Parliament on

 

 

batteries and accumulators and waste batteries.

 

The barred symbol of the rubbish bin shown on the equipment indicates that, at the end of its useful life, the 
product must be collected separately from other waste.

 

Please note that the lithium batteries must be removed from the equipment before it is given as waste and 

 

disposed separately. To remove the batteries refer to the specifications in the user manual. For additional 

 

information and how to carry out disposal, please contact the certified disposal service providers.

 

1. Description

 

The MCF-LW12TERPM is a solar powered sensor that reads temperature, humidity, pressure and PM (PM1,  
PM2.5, PM10) and sends collected data over the LoRaWAN® network. Ideally suited for a wide range of 
applications such as weather stations, urban monitoring, air quality, industrial, environmental or farming 
projects.

 

2. Overview

 

2.1 Technical data

 

 

CPU Cortex M0+ 

EEProm 32Kb

 

Содержание MCF-LW12TERPM




















Отзывы: