M2M MCF-LW12CO2E Скачать руководство пользователя страница 1

 

m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860 

 
 

Table of Contents

 

MCF-LW12CO2E Operating Manual

 

Important safety information

 

Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a 

 

violation of the law. The manufacturer will not be held responsible for any loss or damage resulting from not following the instructions of this 

 

operating manual.

 

Do not dismantle or modify in any way.

 

The device is only intended for indoor use. Do not expose it to moisture.

 

The device is not intended to be used as a reference sensor, and enginko Srl will not be held liable for any damage which may result from inaccurate readings. 
Avoid mechanical stress

 

Do not use any detergent or alcohol to clean the device.

 

Disposal information for users

 

Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of the European Parliament on waste electrical and electronic

   

equipment (WEEE), and pursuant to and in accordance with Article 20 of the Directive 2013/56/EU of the European Parliament on batteries and

  

accumulators and waste batteries.

 

The barred symbol of the rubbish bin shown on the equipment indicates that, at the end of its useful life, the product must be collected separately from  

other waste.

 

Please note that the lithium batteries must be removed from the equipment before it is given as waste and disposed separately. To remove the batteries refer to the 
specifications in the user manual. For additional information and how to carry out disposal, please contact the certified disposal service providers.

 

1. Description

 

The MCF-LW12CO2E is a battery powered sensor for indoor applications that reads temperature, relative humidity, pressure, ambient light, IAQ air quality index 
and CO2. The device sends collected data over the LoRaWAN® network. Ideally suited for a wide range of applications such as home buildings, air quality  
monitoring and energy saving applications.

 

Содержание MCF-LW12CO2E


















Отзывы: