background image

IN BAG #6 (MISCELLANEOUS) 

Clamp Block, 3/8” ................................................................ 8 
Phasing Line Insulator black delrin, 3/4 x 3” ........................ 1 
Balun ‘L’-Bracket, 1” x 1” x 4” .............................................. 1 
Balun Straps ........................................................................ 2 
Fiberglass Insulator, 3/8” x 10” ............................................ 1 
Poly Disk Insulator, 7/8” dia. hole ........................................ 4 
 

IN BAG #7 

Capacitor Caps .................................................................... 32 

 
IN BAG #8

 

Shorting Bar, 15m ................................................................ 8 
Shorting Bar, 15m capacitor tube ........................................ 8 
Shorting Bar, 10m capacitor tube ........................................ 8 
Shorting Bar, 10m ................................................................ 8 
‘T’ Match 

Shorting bar  2 

 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
IN BAG #9

 

Shorting Bar Insulator, Delrin, Black 1-1/2” Dia. .................. 8 

IN HARDWARE BAG #10 

Nut, 3/8-16 ss ...................................................................... 4 
Lockwasher, 3/8” split ring ss .............................................. 4 
Nut, 5/16-18 ss .................................................................... 6 
Lockwasher, 5/16” split ring, ss ........................................... 6 
Bolt, 1/4-20 x 3-1/2” ss ......................................................... 4 
Bolt, 1/4-20 x 3" ss ............................................................... 16 
Bolt, 1/4-20 x 2" ss ............................................................... 20 
Bolt, 1/4-20 x 1-1/2” ss ......................................................... 4 
Nut, 1/4-20 locking, ss ......................................................... 28 

IN HARDWARE BAG #11

 

Screw, 8-32 x 1-1/2" ss ........................................................ 2 
Screw, 8-32 x 1-1/4" ss ........................................................ 58 
Screw, 8-32 x 1" ss .............................................................. 106 
Nut, 8-32 locking, ss ............................................................ 164 

KT34M2 PARTS & HARDWARE 

Содержание KT34M2















Отзывы: