manualshive.com logo in svg

M.T.H. HO 4-6-2 K-4S, Руководство инженера

Поделиться
Скачать
M.T.H. HO 4-6-2 K-4S Скачать руководство пользователя страница 8

SET-UP

Connection of  the Engine and Tender

Your MTH HO 

Steam engine

 features our new wireless close drawbar.  Along 

with providing a mechanical connection of  the tender to the engine, the wireless 
close coupling drawbar  also provides an electrical connection between the engine 
and tender. No assembly is required. 

Smoke Unit Preparation and Use

Your 

engine

 is equipped with a proven fan-driven 

smoke system design featured in MTH products for 
over 10 years. The performance and realism of  this 
system is unparallel in the model train industry.

Your smoke unit comes primed from the factory 
however, before running the smoke unit for more 
than a few minutes, you should add more fluid. 
Add between 10-15 drops initially and whenever 
smoke output diminishes or if  the engine has been 
stored for a long period of  time. We provided some 
fluid with your model to get you started.

The smoke unit is controlled differently depending upon how your run your engine 
so, for particulars on turning it on or off  or setting the output levels, check out the 
features and operation section. You shouldn't run your smoke unit without fluid. 
Doing so can cause overheating and reduce the performance and/or life of  the 
unit. Of  course, we recommend using only MTH ProtoSmoke fluid. Super Smoke 
and LVTS brands also work fine.

Removal/Installation of  Drive Wheel Sets

Your HO Steam engine comes from the factory with traction tire equipped drive 
wheels installed and an alternate set without traction tires available separately in the 
box. The traction tires provide exceptional pulling power on grades and through 
curves but should you prefer the traditional appearance of  steel drive wheels, the 
alternate set can be easily installed by following the steps below.

First, position the engine 
upside down in a foam cradle 
or other soft surface. Using 
the 3mm nut driver tool we 
provided in the box, carefully 
remove the drive rod screws 
(2) on the set of  drive wheels 
located 2nd from the rear.  
There's one on each side.

8

M.T.H. HO 4-6-2 K-4S Steam Engine

Add Smoke Fluid

Содержание HO 4-6-2 K-4S
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды