background image

Additional F Functions

F14-F16 – Idle Sequence

 

Pressing F14, F15, or F16 twice (toggling on then off) will trigger an Idle Sequence 
if  the engine is not moving. These vary from engine to engine and may include 
things like checking the coal load, checking the water level, using the Alemite grease 
gun on the drivers, etc. When triggered, these will run through the sequence that 
varies in duration.

F17 – Extended Start-Up

If  your engine is shut down or you've just applied DCC power pressing F17 twice 
(toggling it on then off) will start the Extended Start-Up sounds. This is very 
similar to F3 except you will hear the crew talking back and forth about getting the 
engine ready to run. 

F18 – Extended Shut-Down

 

If  your engine is already up and running you can play the Extended Shut Down 
sounds by pressing F18 twice (toggling on then off). The Extended Shut Down is 
very similar to F3 in that the engine will ultimately shut down, but in the case of  
Extended Shut Down you will hear the crew talking back and forth about how the 
engine ran, time schedules, etc.

NOTE: The engine must be sitting still in order to trigger F-Functions F14 
through F18

F19 – Labor Chuff

To force the Labor Chuff  sound in a steam engine, press the F19 button once 
(enable F19). As long as F19 is enabled the engine will play its Labor Chuff  sounds. 
To set the sound back to Normal Chuff  press the F19 button again (disable F19).

F20 – Drift Chuff

To force the Drift Chuff  sound in a steam engine, press the F20 button once 
(enable F20). As long as F20 is enabled the engine will play its Drift Chuff  sounds. 
To set the sound back to Normal Chuff  press the F20 button again (disable F20).

F21 – One Shot Doppler

You can set your MTH PS 3-equipped engine to simulate the actual Doppler Effect 
sound a real engine makes as it passes you. To do this, press the F21 button once 
(enable F21) and then listen as the engine makes that pitch shift that mimics the 
Doppler Effect perfectly. Press the F21 button again (disable F21) to shut off  the 
Doppler Effect. With a little practice in timing and speed you can make this happen 
right in front of  you.

19

M.T.H. HO 4-6-2 K-4S Steam Engine

Содержание HO 4-6-2 K-4S
















































Отзывы: