10JV
P. 4 / 4
EM-0862 Rev.4
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System's sole liability, and purchaser's exclusive remedies,
under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To
submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
MAINTENANCE
Regular calibration procedure is explained below:
■
CALIBRATION
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accu-
racy described in the data sheet. When the output is out of
tolerance, recalibrate the unit according to the "ADJUST-
MENT PROCEDURE" explained earlier.
[GROUP 01]
ITEM
INPUT DATA
EXAMPLE (DEFAULT)
CONTENTS
01
S
0, 1
MTSW : MON MODE
Modification code
0 : Data indication only.
1 : All parameters are modifiable.
02
P
Alphanumeric
TG : XXXXXXXXXX
Tag name entry (10 characters max.)
03
P
Number (%)
OUTPER XXX.XX
Output status monitor (%) & simulation output
05
D
No input
INPPER XXX.XX
Input status monitor (%)
06
D
No input
INPVAL XXX.XX
Input status monitor in actual value, same unit as selected in ITEM 10.
10
TYPE OF TRANSMITTER INPUT
D
11
mV-1: 5 – 100mV
D
12
mV-2: 0.05 – 1V
P
13
mV-3: 0.5 – 10V
P
14
mV-6: 1 – 5V
D
15
mV-A: 4 – 20mA
D
16
mV-H: 10 – 50mA
11
P
COARSE INPUT RANGE SELECTION
mV-1
mV-2
mV-3
mV-6 / A / H
(
±
mV)
(
±
V)
(
±
V)
0
INPRNG: XXXX
5
0.05
0.5
1
INPRNG: XXXX
10
0.10
1.0
No Adjustment
2
INPRNG: XXXX
20
0.20
2.0
Needed
3
INPRNG: XXXX
50
0.50
5.0
4
INPRNG: XXXX
100
1.00
10.0
14
P
Actual value
SCLLOW XXXXXX
Input range scaling 0% value
15
P
Actual value
SCLHIG XXXXXX
Input range scaling 100% value
Use the same enginering unit as the coarse range selected in ITEM 11.
19
P
Percentage
FINZER
Fine zero adjustment
Initial status shows actual bias (%).
When data is entered, output (%) is shown.
20
P
Percentage
FINSPN
Fine span adjustment
Initial status shows actual gain (%).
When data is entered, output (%) is shown.
Modification Code
D: No modification (writing) possible. Used only for monitoring (reading).
S: Modifiable at any time.
P: Modifiable only when the MAINTENANCE SWITCH is in the “PRG” mode.
PROGRAMMABLE ITEMS
The following items can be monitored and programmed. For detailed explanations, please refer to the Operation Manual for
Model PU-2
❑
(EM-9255), Section A.
MDF.
CODE
