background image

Installation Instructions

Wall Hoods

Outdoor Applications

IMPORTANT  SAFETY  INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT:

INSTALLER:

OWNER:

SAFETY WARNING:

Save these instructions for the Local Electrical Inspector’s use.

Please leave these instructions with this unit for the owner.

Please retain these instructions for future reference.

Turn off power circuit at the service panel and lock out panel,

before wiring this unit.

 

CAUTION - TO REDUCE THE RISK
OF  FIRE,  ELECTRIC  SHOCK,  OR
INJURY TO PERSONS, OBSERVE THE
FOLLOWING:

1. Use this unit only in the manner 

intended by the manufacturer.  If you 
have any questions, contact 
Lynx Grills, Inc. (888) 289-5969

2. Before servicing or cleaning the unit, 

switch power off at service panel and 
lock the service disconnecting means to
prevent power from being switched on
accidentally. When the service 
disconnecting means cannot be locked,
attach a tag to the service panel to 
indicate power has been switched off 
for maintenance.

3.  Install this Rangehood Only with 

Remote Blower Models Rated 
Maximum 12.8A or Integral Blowers 
Models LOHI and LOHE.

C AU T I O N :   F O R   G E N E R A L
VENTILATION USE ONLY. DO NOT
USE TO EXHAUST HAZARDOUS OR
EXPLOSIVE MATERIALS OR VAPOR.

BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately.
EVACUATE AND CALL THE FIRE 
DEPARTMENT.

3.

2. DO NOT USE WATER, including wet

dish-cloths or towels - a violent steam 
explosion will result.

Use  an  extinguisher 

ONLY

  if:

a.You  know  you  have  a  class  ABC

extinguisher, and you already know
how to operate it.

b.The fire is small and contained in

the area where it started.

c. The fire department is being called.

d.You can fight the fire with your back

to an exit.

CAUTION - TO REDUCE THE RISK
OF  FIRE:

1. Never leave grill unattended.

2. Always turn hood ON when cooking.

3. Clean  ventilating  fans  frequently.

Grease should not be allowed to 
accumulate on fan or filter.

CAUTION - TO REDUCE THE RISK
OF  INJURY TO  PERSONS,  IN THE

1.

1

EVENT  GREASE  FIRE,  OBSERVE 
THE FOLLOWING:

Содержание LOH36




















Отзывы: