Lycoming TEO-540-A1A Скачать руководство пользователя | Manualshive

Страница: 85 / 120

background image

© 2018 Avco Corporation. All Rights Reserved

Engine Operation

October 2018

Page 63

TEO-540-A1A Engine Installation and Operation Manual

NOTICE:

Unstable oil pressure or oil pressure less than 25 psi (172 kPa) could be an

indication of obstructed or interrupted oil flow or air in the oil hose. In this case,
stop, and have a technician look at the oil hoses.
Upon engine start, if smoke comes from a newly installed engine, after the first start,
there could have been some preservative oil in the cylinders, induction system,
and/or fuel nozzles/lines. If oil pressure is normal and the engine operates smoothly,
continue to operate the engine until the smoke clears. Otherwise stop the engine,
contact Lycoming Engines.

13.

After the engine is put back into service after storage, maintenance, repair, fault isolation,
overhaul, or rebuild, complete the operational test (as per “Step 4. Complete the Operational
Test” in this chapter.).

Step 3. Engine Run-Up

WARNING

IF DURING ENGINE RUN-UP OR ENGINE IDLE, ANY OPERATIONAL

PROBLEMS OCCUR, DO NOT TAKE-OFF. IDENTIFY AND CORRECT
THE CAUSE OF THE PROBLEM AND REPEAT THIS RUN-UP.

Complete the engine run-up as follows:

1.

Start the engine.

2.

Make sure the oil temperature is above the specified minimum.

WARNING

IF THE ENGINE IS OPERATED AT LOW OIL PRESSURE OR LOW OIL

LEVEL, THE ENGINE CAN MALFUNCTION OR STOP.

3.

Make sure the oil pressure and oil temperatures are within operating range (Appendix A).

4.

Increase the power control to 1200 rpm and let it stabilize.

5.

Pull the EEC/ECU circuit breaker.

6.

As the engine continues to operate, increase the power control from 1200 to 1400 rpm over 2
minutes. Allow the engine to stabilize and continue to operate.

7.

Decrease the power control back to 1200 rpm over 2 minutes. Allow the engine to stabilize
and continue to operate.

8.

Reset the EEC/ECU circuit breaker. Decrease the power control to IDLE and allow the
engine to stabilize.

NOTICE:

Do not use the Field Service Tool (FST) during flight.

9.

Complete “Step 4. Pre-Flight Test” section in this chapter.

Step 4. Pre-Flight Test

The Pre-Flight Test (PFT) is done during engine run-up before flight to make sure that:

•

The engine is operating correctly

•

Both ECU channels are operating correctly to control the engine

•

There are no latent failures on the secondary channel of the ECU before each flight.

«
...
83
84
85
86
87
...
»

Содержание TEO-540-A1A

























































































































Отзывы:

Нет отзывов

Похожие инструкции для TEO-540-A1A

Бренд: 3W Страницы: 20

Бренд: Eaton Страницы: 16

Бренд: Hacker Страницы: 10

Бренд: WÜRGES Страницы: 24

Бренд: Hacker Страницы: 2

Бренд: Hacker Страницы: 7

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

E ACTION SI 332 AC

Бренд: Era Inn Страницы: 2

Бренд: WilTec Страницы: 16

Бренд: GEA Bock Страницы: 62

Бренд: Royal Enfield Страницы: 152

Бренд: Briggs & Stratton Страницы: 14

Бренд: Ford Страницы: 6

Бренд: Vetus Страницы: 108

Бренд: TRAXX Страницы: 8

Бренд: 3W Страницы: 19

Бренд: Cuyuna Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды